소개

Steps to remove LG VX8550 slider mechanism

Slide the battery release up.
  • Slide the battery release up.

댓글 쓰기

Remove the battery by lifting away from the case.
  • Remove the battery by lifting away from the case.

댓글 쓰기

Remove the 2 screw covers next to the rear speaker with a Push Pin.
  • Remove the 2 screw covers next to the rear speaker with a Push Pin.

댓글 쓰기

Remove the 4 cover screws with a Philips #00 screwdriver.
  • Remove the 4 cover screws with a Philips #00 screwdriver.

댓글 쓰기

Use the iPod opening tool to pry off the back casing.
  • Use the iPod opening tool to pry off the back casing.

댓글 쓰기

Continue sliding the iPod opening tool around the seam of the casing to separate the front and back casings.
  • Continue sliding the iPod opening tool around the seam of the casing to separate the front and back casings.

댓글 쓰기

Separate the casing halves.
  • Separate the casing halves.

  • Be sure to keep track of the side buttons as they fall out.

댓글 쓰기

Remove the 2 screws from the back of the phone with a Phillips #00 Screwdriver.
  • Remove the 2 screws from the back of the phone with a Phillips #00 Screwdriver.

댓글 쓰기

Carefully lift up on the motherboard to see the ribbon cables underneath.
  • Carefully lift up on the motherboard to see the ribbon cables underneath.

  • Use the spudger to carefully disconnect the ribbon cable from the motherboard.

댓글 쓰기

Remove the motherboard from the front casing by lifting straight up.
  • Remove the motherboard from the front casing by lifting straight up.

댓글 쓰기

Lay the phone with the screen facedown.
  • Lay the phone with the screen facedown.

  • The 6 slider screws are visible.

댓글 쓰기

Peel back but don't remove the blue tape to access the 2 center screws.
  • Peel back but don't remove the blue tape to access the 2 center screws.

  • Remove the 6 slider screws with the Phillips #00 screwdriver.

댓글 쓰기

Lift the keypad housing away from the slider.
  • Lift the keypad housing away from the slider.

댓글 쓰기

Remove the 2 screw covers next to the speaker with a push pin next to the camera.
  • Remove the 2 screw covers next to the speaker with a push pin next to the camera.

댓글 쓰기

Remove the 6 screws with a Phillips #00 Screwdriver.
  • Remove the 6 screws with a Phillips #00 Screwdriver.

댓글 쓰기

Use the ipod opening tool to pry the screen casing and the slider mechanism apart from each other.
  • Use the ipod opening tool to pry the screen casing and the slider mechanism apart from each other.

댓글 쓰기

Carefully lift the slider mechanism to see the ribbon cables underneath.
  • Carefully lift the slider mechanism to see the ribbon cables underneath.

댓글 쓰기

Slide ribbon cable through the slider mechanism.
  • Slide ribbon cable through the slider mechanism.

댓글 쓰기

Separate the two halves.
  • Separate the two halves.

댓글 쓰기

With the slider mechanism separated from the screen casing the 8 screws securing the slider mechanism are visible.
  • With the slider mechanism separated from the screen casing the 8 screws securing the slider mechanism are visible.

  • Remove the 8 screws.

댓글 쓰기

Remove slider mechanism.  Now is a good time to clean slider mechanism if sticky.
  • Remove slider mechanism. Now is a good time to clean slider mechanism if sticky.

댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Nathan Jones

회원 가입일: 2010년 04월 10일

83 평판

안내서 20개 작성하였습니다

Cal Poly, Team 34-55, Forte Spring 2010 Cal Poly, Team 34-55, Forte Spring 2010 회원

CPSU-FORTE-S10S34G55

5 회원들

안내서 20개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 0

전체 시간: 2,993