메인 콘텐츠로 스킵하기

소개

Is your screen filled with black spots or not displaying images properly? Consider using this guide to replace the display of your device.

부품

지정된 부품이 없습니다.

  1. Make sure to power down and turn off your device before proceeding with the repair. Flip your laptop over so that the backside is facing you.
    • Make sure to power down and turn off your device before proceeding with the repair.

    • Flip your laptop over so that the backside is facing you.

  2. Using a Phillips #1 screwdriver, remove the eight screws securing the backplate.
    • Using a Phillips #1 screwdriver, remove the eight screws securing the backplate.

  3. Using the metal spudger, wedge it in the seam where the backplate meets the front plate and run the tool along the seam to separate the backplate. Using the metal spudger, wedge it in the seam where the backplate meets the front plate and run the tool along the seam to separate the backplate.
    • Using the metal spudger, wedge it in the seam where the backplate meets the front plate and run the tool along the seam to separate the backplate.

  4. Remove the back panel from the device.
    • Remove the back panel from the device.

  5. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now
  6. Use the Phillips #1 screwdriver to remove the five screws securing the display mounts. Use the Phillips #1 screwdriver to remove the five screws securing the display mounts. Use the Phillips #1 screwdriver to remove the five screws securing the display mounts.
    • Use the Phillips #1 screwdriver to remove the five screws securing the display mounts.

  7. Use the metal spudger to pry up the lever securing the ribbon cable in it's connection housing. Use the metal spudger to pry up the lever securing the ribbon cable in it's connection housing. Use the metal spudger to pry up the lever securing the ribbon cable in it's connection housing.
    • Use the metal spudger to pry up the lever securing the ribbon cable in it's connection housing.

  8. Grab hold of the ribbon cable and pull it out of it's connection housing. Grab hold of the ribbon cable and pull it out of it's connection housing. Grab hold of the ribbon cable and pull it out of it's connection housing.
    • Grab hold of the ribbon cable and pull it out of it's connection housing.

  9. Disconnect the white and blue wires connected to the mounted circuit by grabbing them close to the connection and pulling upward. Disconnect the white and blue wires connected to the mounted circuit by grabbing them close to the connection and pulling upward.
    • Disconnect the white and blue wires connected to the mounted circuit by grabbing them close to the connection and pulling upward.

  10. Use the Phillips #1 screwdriver to remove the two screws securing the metal plate to expose the wire connection. Use the Phillips #1 screwdriver to remove the two screws securing the metal plate to expose the wire connection.
    • Use the Phillips #1 screwdriver to remove the two screws securing the metal plate to expose the wire connection.

  11. Disconnect the wire by pulling it upward from the motherboard. Disconnect the wire by pulling it upward from the motherboard.
    • Disconnect the wire by pulling it upward from the motherboard.

  12. Unclip the 5 wires connected to the display assembly from the motherboard and move them out of the way. Unclip the 5 wires connected to the display assembly from the motherboard and move them out of the way. Unclip the 5 wires connected to the display assembly from the motherboard and move them out of the way.
    • Unclip the 5 wires connected to the display assembly from the motherboard and move them out of the way.

  13. Now that the display assembly is disconnected from the main body, lift both of the mounting brackets and remove the display assembly from the main body. Now that the display assembly is disconnected from the main body, lift both of the mounting brackets and remove the display assembly from the main body. Now that the display assembly is disconnected from the main body, lift both of the mounting brackets and remove the display assembly from the main body.
    • Now that the display assembly is disconnected from the main body, lift both of the mounting brackets and remove the display assembly from the main body.

결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

Terelle Montalvo

회원 가입일: 2018년 10월 22일

1,096 평판

안내서 8개 작성하였습니다

UMass Dartmouth, Team S1-G5, Simcock Fall 2018 UMass Dartmouth, Team S1-G5, Simcock Fall 2018 회원

UMASSD-SIMCOCK-F18S1G5

3 회원들

안내서 8개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 5

지난 7일: 12

지난 30일: 54

전체 시간: 427