Skip to main content

소개

To remove the screen module off the laptop board follow the following steps

부품

No parts specified.

  1. Turn off the computer.
    • Turn off the computer.

    • Disconnect the charging cable from the computer.

    • Failure to unplug the cable could result in electric shock.

  2. Flip the computer upside down.
    • Flip the computer upside down.

    • The red rectangle shows the location of the battery.

  3. Locate the two switches that lock the battery. Push the left-hand switch outward into the "unlocked" position. Locate the two switches that lock the battery. Push the left-hand switch outward into the "unlocked" position. Locate the two switches that lock the battery. Push the left-hand switch outward into the "unlocked" position.
    • Locate the two switches that lock the battery. Push the left-hand switch outward into the "unlocked" position.

  4. Now push and hold the right clip to the right while using your other hand to gently slide the battery away from the computer. Now push and hold the right clip to the right while using your other hand to gently slide the battery away from the computer. Now push and hold the right clip to the right while using your other hand to gently slide the battery away from the computer.
    • Now push and hold the right clip to the right while using your other hand to gently slide the battery away from the computer.

  5. Locate the hard drive enclosure (marked by the red rectangle).
    • Locate the hard drive enclosure (marked by the red rectangle).

  6. Use a small Phillips screwdriver to unscrew the single screw that holds down the hard drive enclosure cover. The screw is designed to remain within the plastic cover. Don't worry about extracting it completely.
    • Use a small Phillips screwdriver to unscrew the single screw that holds down the hard drive enclosure cover.

    • The screw is designed to remain within the plastic cover. Don't worry about extracting it completely.

    • Carefully remove the hard drive enclosure cover.

  7. Gently pull the black pull tab out from above the hard drive. Continue pulling on the pull tab until the hard drive and the two plastic rails come out of the enclosure. Pull on the tab firmly but slowly. The hard drive should come out of the enclosure effortlessly. Pull on the tab firmly but slowly. The hard drive should come out of the enclosure effortlessly.
    • Gently pull the black pull tab out from above the hard drive. Continue pulling on the pull tab until the hard drive and the two plastic rails come out of the enclosure.

    • Pull on the tab firmly but slowly. The hard drive should come out of the enclosure effortlessly.

  8. Remove the plastic rails from the old SSD/hard drive and place them on the new SSD/hard drive. Remove the plastic rails from the old SSD/hard drive and place them on the new SSD/hard drive. Remove the plastic rails from the old SSD/hard drive and place them on the new SSD/hard drive.
    • Remove the plastic rails from the old SSD/hard drive and place them on the new SSD/hard drive.

  9. 아이폰 배터리 수리 키트

    Only $29.99

    Buy Now

    아이폰 배터리 수리 키트

    Only $29.99

    Buy Now
  10. There are 2 screws securing the keyboard. You can identify them by a small keyboard symbol (marked by an orange rectangle in the second picture). Once you have located the two screws, remove them with a small Phillips screwdriver. Once you have located the two screws, remove them with a small Phillips screwdriver.
    • There are 2 screws securing the keyboard. You can identify them by a small keyboard symbol (marked by an orange rectangle in the second picture).

    • Once you have located the two screws, remove them with a small Phillips screwdriver.

  11. This step is not required. Gently pull the strip out from the case. Gently pull the strip out from the case.
    • This step is not required.

    • Gently pull the strip out from the case.

  12. Use a a plastic spudger (or a flat screwdriver) to push the keyboard towards the screen. This will pop the bottom of the keyboard out of the casing. Use a a plastic spudger (or a flat screwdriver) to push the keyboard towards the screen. This will pop the bottom of the keyboard out of the casing.
    • Use a a plastic spudger (or a flat screwdriver) to push the keyboard towards the screen. This will pop the bottom of the keyboard out of the casing.

  13. Carefully lift the keyboard so that you can access its connector. Carefully lift the keyboard so that you can access its connector.
    • Carefully lift the keyboard so that you can access its connector.

  14. Carefully unplug the connector by pulling. Carefully unplug the connector by pulling.
    • Carefully unplug the connector by pulling.

  15. You are done - the keyboard is not connected to the laptop any more and can be replaced.
    • You are done - the keyboard is not connected to the laptop any more and can be replaced.

  16. Remove five 5.7mm screws from the bottom. Remove five 5.7mm screws from the bottom. Remove five 5.7mm screws from the bottom.
    • Remove five 5.7mm screws from the bottom.

  17. Unscrew two 5.7mm screws from the top of the bottom of the laptop. Unscrew two 5.7mm screws from the top of the bottom of the laptop.
    • Unscrew two 5.7mm screws from the top of the bottom of the laptop.

  18. Pull the palm rest off the laptop board. Pull the palm rest off the laptop board.
    • Pull the palm rest off the laptop board.

  19. Unlock the white seal and disconnect the blue cable. Unlock the white seal and disconnect the blue cable.
    • Unlock the white seal and disconnect the blue cable.

  20. Carefully disconnect blue and red cables and remove them from plastic case. Carefully disconnect blue and red cables and remove them from plastic case. Carefully disconnect blue and red cables and remove them from plastic case.
    • Carefully disconnect blue and red cables and remove them from plastic case.

  21. Unlock white seal and diconnect blue cable from upper corner. Unlock white seal and diconnect blue cable from upper corner.
    • Unlock white seal and diconnect blue cable from upper corner.

  22. Remove two 4.1mm screws from the black frame. Remove two 4.1mm screws from the black frame.
    • Remove two 4.1mm screws from the black frame.

  23. Carefully pull off black frame from laptop board. Carefully pull off black frame from laptop board. Carefully pull off black frame from laptop board.
    • Carefully pull off black frame from laptop board.

  24. Carefully lift the screen module straight up to detach from board.
    • Carefully lift the screen module straight up to detach from board.

결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

Lino Virgen

회원 가입일: 2016년 10월 10일

721 평판

안내서 3개 작성하였습니다

Texas Tech, Team 6-3, Bennett Fall 2016 Texas Tech, Team 6-3, Bennett Fall 2016 회원

TTU-BENNETT-F16S6G3

4 회원들

안내서 3개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 2

지난 7일: 25

지난 30일: 124

전체 시간: 5,454