메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Mac mini (PowerPC) Upper Case Replacement

작성자 iRobot (또 다른 기여자 6명)
  • 댓글 2
  • 즐겨찾기 5
  • 완료: 9

난이도

보통

단계

6

소요 시간

시간 제안??

섹션

1

플래그

0

소개

How to remove the upper case.

도구

해당 도구 구매

부품

No parts specified.

  1. Power down your Mac mini, disconnect all of the cables, and flip it over. Insert the Jimmy into the crack between the aluminum top housing and the plastic lower housing.

    • Power down your Mac mini, disconnect all of the cables, and flip it over.

    • Insert the Jimmy into the crack between the aluminum top housing and the plastic lower housing.

    • The Jimmy should reach a stop about 3/8" down.

    편집

  2. Gently bend the Jimmy outwards to pry the crack open a little larger and lift the lower housing up a small amount. There are several plastic clips on the lower housing that fit into a channel in the aluminum top housing. Your goal is to use the Jimmy to push these clips inward enough to free them from the channel, while gently pulling up on the lower housing. There are several plastic clips on the lower housing that fit into a channel in the aluminum top housing. Your goal is to use the Jimmy to push these clips inward enough to free them from the channel, while gently pulling up on the lower housing.

    • Gently bend the Jimmy outwards to pry the crack open a little larger and lift the lower housing up a small amount.

    • There are several plastic clips on the lower housing that fit into a channel in the aluminum top housing. Your goal is to use the Jimmy to push these clips inward enough to free them from the channel, while gently pulling up on the lower housing.

    편집

  3. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

  4. Once you have the first side free, rotate the Mac mini and start prying up on the front edge. Use the same prying motion to both bend the clips inward and lift the lower housing up out of the top housing.

    • Once you have the first side free, rotate the Mac mini and start prying up on the front edge.

    • Use the same prying motion to both bend the clips inward and lift the lower housing up out of the top housing.

    편집

  5. You may need to move the Jimmy along the edge to pry up all of the clips. Be patient and do a little bit at a time. You may need to move the Jimmy along the edge to pry up all of the clips. Be patient and do a little bit at a time.

    • You may need to move the Jimmy along the edge to pry up all of the clips. Be patient and do a little bit at a time.

    편집

  6. Keep working around the perimeter, freeing the clips along the final edge. Keep working around the perimeter, freeing the clips along the final edge.

    • Keep working around the perimeter, freeing the clips along the final edge.

    편집

  7. Flip the Mac mini back over and lift the top housing off of the lower housing. Flip the Mac mini back over and lift the top housing off of the lower housing.

    • Flip the Mac mini back over and lift the top housing off of the lower housing.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 9명이 해당 안내서를 완성하였습니다.

첨부 문서

작성자

다른 기여자 6명과 함께

iRobot

회원 가입일: 2009년 09월 24일

1 평판

안내서 623개 작성하였습니다

배지: 35

배지 +32개 더

댓글 한 개

의견 추가하세요

those Putty Knifes are:

too smal

too sharp

too expensive.

Better use a 100mm broad Spatula; (opens all the claws in on step)

out of plastic is good enough and cheap.

And use two of them at one time.

spatula - 답글

댓글 쓰기

1024

조회 통계:

지난 24시간: 3

지난 7일: 4

지난 30일: 22

전체 시간: 9,540