이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a coin or spudger to rotate the battery-locking screw 90 degrees clockwise.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the three evenly-spaced Phillips screws from along the rear wall of the battery compartment.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift up on L-shaped memory cover, slide it to the right, and lift it out of the computer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 3 screws:
-
One 11 mm Phillips #00 in the middle of the case.
-
Two 14.5 mm Phillips #00.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 3 screws from the rear wall of the battery compartment:
-
Two 3 mm Phillips #00. (A1181 has three 3 mm screws and one 4 mm.)
-
One 4 mm Phillips #00 on the right side.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two 6 mm Phillips #00 screws from either side of the right wall of the battery compartment (not the ones closest to the battery connector).
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the four 3 mm indicated Phillips #00 screws from the front wall of the battery compartment. When working from the left, remove the 2nd, 4th, 7th and 9th screw.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 4 screws from the back of the computer:
-
Two 7 mm shouldered Phillips on the far sides.
-
Two 10.5 mm Phillips toward the center.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two 5.2 mm shouldered Phillips #00 screws from the optical side of the computer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Starting near the display and working around to the front of the computer, pry up on the upper case. It is held with clips on the right above the optical drive. These will release with some firm lifting pressure.
-
Be careful when prying up the upper case. It's very easy to slice open a fingertip and thus provide the blood sacrifice the Mac gods sometimes require of those who insist on doing their own repairs.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While holding up the upper case (from the bottom or the top), use a spudger to pry up the orange trackpad and keyboard cable from its connector.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the white plastic tab attached to the hard drive and pull it to the left, removing the hard drive from the computer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two Phillips screws from the front edge of the optical drive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Disconnect the newly-revealed display data cable. If there is no pull-tab on the top of the connector, it may be helpful to use a spudger to disconnect this connector.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Peel up the foil tape between the fan and the optical drive.
-
Remove the 8.5 mm Phillips screw securing the display data cable to the metal framework.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull up the display data cable from along the edge of the optical drive to reveal a silver Phillips screw.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the 2.8 mm Phillips screw securing the optical drive.
-
After removing the screw, push the metal tab backwards, towards the fan, to release the front of the optical drive.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the Bluetooth antenna board from the right side of the optical drive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Deroute the hard drive cable from along the front of the optical drive.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the front edge of the optical drive and slide it up and out of the computer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 3 screws:
-
Two 3 mm Phillips near the right speaker.
-
One 6 mm Phillips threaded through a hole in a plastic finger above the subwoofer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Using a spudger, gently pry up the white plastic slot and slide the metal c-channel to the right and away from the display.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger to carefully disconnect the microphone cable from the logic board. You'll want to work from side to side, and slowly wiggle the connector out of its socket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift up on the black right speaker cable with one hand, and deroute the silver microphone cable from the silver metal clip just above the right RAM slot.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Deroute the silver microphone cable and gray display data cable from the tabs at the bottom of the subwoofer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the single 3.2 mm Phillips screw securing the ground loop in the display data cable located just above the Bluetooth board.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Disconnect the two antenna cables from the Airport card, and the black inverter cable from the logic board. (Pull vertically on all three.)
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the following 2 screws from the right hinge mount:
-
One 6 mm Phillips on the left side of the hinge mount.
-
One 10 mm Phillips on the right side of the hinge mount.
-
Lift the right hinge mount out of the computer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Hold the display with one hand while removing the screws from the left hinge mount.
-
Remove the following 3 screws from the left hinge mount:
-
One 6 mm smaller diameter Phillips from the right side.
-
One 6 mm larger diameter Phillips from the middle.
-
One 10 mm Phillips from the left side.
-
Lift the left hinge mount out of the computer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the display assembly on either side, and lift it up and out of the computer.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
이 단계에 사용된 도구:Plastic Cards$2.99-
Use a thin plastic card to release the tabs and their clips holding the front display bezel to the display assembly. There are five tabs along the left side of the display bezel.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Continue to free the tabs along the the top edge of the display assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift up the front display bezel from the top and use your plastic card to free the tabs along the bottom edge of the display bezel.
-
After freeing all holding tabs, lift the front display bezel away from the display assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a metal spudger or another thin tool to carefully pry the gray plastic clips off the tabs molded into the front display bezel. A 0.8mm flat screwdriver may be useful for this step. You may find that it's easier to remove some of these clips by prying up on their long sides.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Insert one end of the retaining clip beneath the edge of its recess cut into the LCD bracket.
-
Use the edge of a spudger to push the short hook tab on the underside of the other end of the retaining clip into the recess cut into the LCD bracket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
While holding the display down with one hand, use your other hand to lift the left end of the clutch cover off the clutch hinge and guide the inverter cable and AirPort cables through the gap in the clutch cover. If the cables snag on the two hooked tabs on the inside end of the clutch cover, free them carefully.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift up the right end of the clutch cover while guiding the display data and iSight cables through the gap and the two hooked tabs at the right end of the clutch cover. If the cables snag on the two hooked tabs, free them carefully.
-
Lift the clutch cover off of the display assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the small piece of foam tape stuck down above each of the bezel covers, at the lower left and right corners.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger to slide the left bezel cover towards the LCD panel.
-
Lift the left bezel cover off the display assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use a spudger to slide the right bezel cover toward the LCD panel.
-
Lift the right bezel cover off the display assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the inverter out of the display slightly and disconnect the backlight cable from its right side.
-
Place the inverter back down in its recess.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the single 3.2 mm Phillips screw securing the display data cable to the right clutch hinge.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Move the display data cable out from under the mounting arm of the right clutch hinge.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the twelve 4.2 mm Phillips screws securing the LCD assembly to the rear display bezel.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Raise the bottom edge of the LCD assembly slightly, then slide it down slightly to free its upper edge from a slight overhang in the rear display bezel.
-
Lift it out of the rear display bezel, minding any cables that may get caught.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove all of the pieces of tape securing your display data cable to the back of the LCD.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
De-route the microphone cable from the clips along the side and top of the LCD assembly.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the two 2.2 mm Phillips screws securing the iSight board to its bracket.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the flat end of a spudger to pry the camera out of its recess.
-
Remove the iSight from the display.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Use the tip of a spudger to push the microphone out of the iSight bezel.
-
Display data cable remains.
-
다른 27명이 해당 안내서를 완성하였습니다.
댓글 2개
Truly superb set of photos and instructions. I’d love to be able to buy a replacement data display cable, but no one seems to stock them.