주요 콘텐츠로 건너뛰기

기기를 수리하세요

수리할 권리

상점

부품

지정된 부품이 없습니다.

  1. Spudger/스퍼저의 평평한 끝을 사용하여 트랙패드 커넥터를 로직 보드 소켓에서 위로 들어올리세요. Spudger/스퍼저의 평평한 끝을 사용하여 트랙패드 커넥터를 로직 보드 소켓에서 위로 들어올리세요.
    • Spudger/스퍼저의 평평한 끝을 사용하여 트랙패드 커넥터를 로직 보드 소켓에서 위로 들어올리세요.

    The trackpad cable can also be of a different type where you pull the tape on it

    Rogier van der Heide - 답글

  2. 트랙패드 케이블을 배터리에서 위로 들어 올려 고정하는 접착제에서 분리하세요. 케이블을 손상하지 않도록 주의하세요. 쉽게 떨어지지 않으면 iOpener, 열선 총, 또는 헤어 드라이어를 사용하여 약간의 열을 가해 접착제를 부드럽게한 다음 다시 시도하세요.
    • 트랙패드 케이블을 배터리에서 위로 들어 올려 고정하는 접착제에서 분리하세요.

    • 케이블을 손상하지 않도록 주의하세요. 쉽게 떨어지지 않으면 iOpener, 열선 총, 또는 헤어 드라이어를 사용하여 약간의 열을 가해 접착제를 부드럽게한 다음 다시 시도하세요.

    On the picture above, it looks like, that the CIF cable for the keyboard, located right to the trackpad cable, should also be separated, but this is not necessary. You can leave it attached.

    anmeldung - 답글

    What helped release the cable was to place the body of the spudger under the cable and rotate it upward as I gently pulled it down to release the cable from the adhesive. It may not have been necessary, but it did help.

    Todd S. Jones - 답글

  3. SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits

    SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits
  4. 필요한 경우, 트랙패드 케이블 커넥터를 덮고 있는 테이프를 떼세요. Spudger/스퍼저의 끝을 사용하여 ZIF 커넥터의 고정 탭을 뒤집으세요. Spudger/스퍼저의 끝을 사용하여 ZIF 커넥터의 고정 탭을 뒤집으세요.
    • 필요한 경우, 트랙패드 케이블 커넥터를 덮고 있는 테이프를 떼세요.

    • Spudger/스퍼저의 끝을 사용하여 ZIF 커넥터의 고정 탭을 뒤집으세요.

    Overall, I really enjoyed this project and it was a complete success but this step is the one spot I came up short. I forgot to flip the retaining tab back down when I reassembled and I got a totally unresponsive keyboard and trackpad before I opened it back up and realized I had forgotten this tiny but crucial step.

    nathan taylor - 답글

    I also forgot to flip the ZIF connector. Thankfully my trackpad worked after.

    Make sure to flip the ZIF connector before putting the trackpad cable back, too.

    ibash - 답글

    I did not remove this retaining clip for fear of not getting it plugged in again then just carefully folded it back to clear battery instal

    Peter Stoll - 답글

    This was the most challenging part of the installation. Putting this tab back, it's so fragile and difficult to put back. I thought it was going to get damaged but it worked.

    Gaetano Daidone - 답글

    Like Peter, I just folded it back a bit and had care to keep it out of the way. I think it is much better than the risk involved with taking it out.

    All in all it found it a bit less difficult than I expected - As with all the work I have done on different Apple products: Slow and careful work and following the instructions - including all the comments - seems to be the best advice.

    Adam Griggs - 답글

    I have a semi responsive trackpad and an unrecognized keyboard. Any suggestions?

    Daniel Lynn - 답글

    Daniel- remove and put back again the cable on the ZIF connector, making sure it is pushed all the way in before closing the retainer clip. May have a partially reinserted cable.

    drrobins - 답글

  5. 트랙패드 컨트롤 보드 ZIF 소켓에서 트랙패드 케이블을 똑바로 당겨 빼세요. 트랙패드 컨트롤 보드 ZIF 소켓에서 트랙패드 케이블을 똑바로 당겨 빼세요.
    • 트랙패드 컨트롤 보드 ZIF 소켓에서 트랙패드 케이블을 똑바로 당겨 빼세요.

    With all due respect, step # 19 and 20 pics shows the ZIF socket on the trackpad board, not the Mac logic board, I think...

    See step #17 which seems to be correct. There is an inconsistency in the guide.

    Just to be sure...

    Bart Van Dessel - 답글

    This was the most difficult step for me. It was hard to locate the retaining tab on the ZIF connector and the trackpad cable had some adhesive on the bottom of it and it was difficult to remove from the socket. Be patient….

    Gary Bain - 답글

    I skipped this two steps (19&20) , just bent the flat fable when taking the battery out.

    Aleš Smokvina - 답글

    This does look the most frightening part of the process, that connector looks really flimsy. Is it ok to just bend it back and leave it connected as suggested?

    Jack Sukerman - 답글

    This is the only step I skipped, as Gary Bain mentioned above there was adhesive which made it difficult to remove, and it’s probably the only step worth skipping.

    John Davis - 답글

    Can you buy replacements for this trackpad control board? They dont seem to come with new trackpads.

    Rachel MacLeod - 답글

    The ZIF retaining tab is a tiny black plastic bar. Pull the trackpad cable HORIZONTALLY out of the socket.

    Richard Johnson - 답글

  6. 배터리 보드를 상단 케이스에 고정하는 3.7mm T5 Torx/톡스 나사 한 개를 풀어주세요.
    • 배터리 보드를 상단 케이스에 고정하는 3.7mm T5 Torx/톡스 나사 한 개를 풀어주세요.

    If lost where could I find a replacement for this screw?

    Justin - 답글

결론

기기를 재조립하려면, 이 지침을 역순으로 따르세요.

다른 한 분이 해당 안내서를 완성하였습니다.

다음 번역가들에게 특별히 감사 드립니다:

100%

Christian Kim님은 저희가 세상을 수리하는데 동참하신 분입니다! 기여하시겠습니까?
번역 시작하기 ›

Sam Goldheart

회원 가입일: 2012년 10월 18일

419,971 평판

안내서 547개 작성하였습니다

iFixit iFixit 회원

Community

128 회원들

안내서 13,059개 작성하였습니다

Why remove the screw in step 5?

Ari Cooper - Davis - 답글

Yes @sam , why should you remove the screw in step 5? Is this a mistake?

lmdehaas - 답글

Step 5: Remove the single 3.7 mm T5 Torx screw.

Step 6: Re-screw single 3.7 mm T5 Torx screw.

David Grabowski - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 2

30일 전: 16

전체 시간: 1,595