기기를 수리하세요 커뮤니티에 동참하기 상점

MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement

소개

Use this guide to remove or replace the heat sink.

Don't forget to follow our thermal paste application guide after you have removed your heat sink.

필요한 것

  1. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement, Lower Case: 1 단계, 이미지 1/1
    이 단계에 사용된 도구:
    Magnetic Project Mat
    $19.99

    • Remove the following ten screws securing the lower case to the upper case:

    • Two 2.3 mm P5 Pentalobe screws

    • Eight 3.0 mm P5 Pentalobe screws

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your device.

    편집

  2. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 2 단계, 이미지 1/1

    • Wedge your fingers between the upper case and the lower case.

    • Gently pull the lower case away from the upper case to remove it.

    편집

  3. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 3 단계, 이미지 1/2 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 3 단계, 이미지 2/2

    • The lower case is connected to the upper case with two plastic clips near its center.

    • During reassembly, gently push down the center of the lower case to reattach the two plastic clips.

    편집

  4. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement, Battery Connector: 4 단계, 이미지 1/1

    • If necessary, remove the plastic cover adhered to the battery contact board.

    편집

  6. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 5 단계, 이미지 1/2 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 5 단계, 이미지 2/2

    • Use the flat end of a spudger to lift the battery connector straight up out of its socket on the logic board.

    • Be sure you lift up only on the connector itself, not the socket, or you risk permanent damage to the logic board.

    편집

  7. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 6 단계, 이미지 1/1

    • Bend the battery connector up out of the way to prevent accidental contact with its socket during your repair.

    편집

  8. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement, Heat Sink: 7 단계, 이미지 1/3 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement, Heat Sink: 7 단계, 이미지 2/3 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement, Heat Sink: 7 단계, 이미지 3/3

    • Carefully remove the rubber fan bumper from the edge of the heat sink.

    • The fan bumper wraps around the heat sink and fits into slots in the fan duct. During reassembly, be sure to fit the tabs into the notches in the fan duct.

    편집

  9. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 8 단계, 이미지 1/2 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 8 단계, 이미지 2/2

    • Use the flat end of a spudger to peel the four foam stickers off of the heat sink screws.

    편집

  10. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 9 단계, 이미지 1/1

    • Remove the following screws securing the heat sink to the logic board:

    • Four 2.6 mm T5 screws

    • One 2.4 mm Phillips #000 screw

    편집

  11. MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 10 단계, 이미지 1/2 MacBook Pro 13" Retina Display Mid 2014 Heat Sink Replacement: 10 단계, 이미지 2/2
    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 13명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Sam Goldheart

회원 가입일: 10/18/12

457,183 평판

안내서 537개 작성하였습니다

Badges: 48

배지 +45개 더

팀

iFixit iFixit 회원

Community

138 회원들

안내서 16,920개 작성하였습니다

댓글 한 개

Do I need Anti-Static Wrist Strap ?

if so, where do i connect it, to laptop ?

mikele - 답글

댓글 쓰기

조회 통계:

24 시간 전: 3

7일 전: 22

30일 전: 127

전체 시간: 19,406