주요 콘텐츠로 건너뛰기

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

MacBook Pro 13" Touch Bar 2017 스크린 교체

필요한 것

  1. MacBook Pro 13" Touch Bar 2017 스크린 교체, Auto Boot/자동 부팅 비활성화: 1 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, Auto Boot/자동 부팅 비활성화: 1 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, Auto Boot/자동 부팅 비활성화: 1 단계, 이미지 3/3
    • 이 절차를 시작하기 전에 Mac Auto Boot/자동 부팅 기능을 비활성화해야 합니다. Auto Boot/자동 부팅은 덮개를 열면 Mac 전원을 켜며 분해 도중 실수로 촉발할 수 있습니다. 이 안내서를 사용하거나 아래의 약식 지침을 따라서 Auto Boot/자동 부팅을 비활성화 하세요. 이 지침은 모든 Mac에서 작동하지 않을 수 있습니다.

    • Mac 전원을 켜고 Terminal/터미널을 시작하세요.

    • 다음 명령을 복사하여 Terminal/터미널에 붙여 넣으세요 (또는 정확히 입력하세요).

    • sudo nvram AutoBoot=%00

    • [return]을 누르세요. 관리자 암호 입력 메시지가 나타나면 관리자 암호를 입력하고 [return]을 다시 누르세요. 참고: return 키는 ⏎ 또는 "enter/입력"으로 표시되어 있을 수도 있습니다.

    • 이제 Mac 전원을 안전하게 끄고, 실수로 전원을 켜지 않으며, 하단 케이스를 열 수 있습니다.

    • Mac 수리를 완료하고 성공적으로 재조립하면 다음 명령을 사용하여 Auto Boot/자동 부팅을 다시 활성화 하세요.

    • sudo nvram AutoBoot=%03

    Is this step necessary? I can’t perform this step as I am attempting to repair water damage and need to remove logic board & most likely replace the battery.

    Macrepair SF - 답글

    @mac_medic You definitely don’t want the power coming on while the board is wet. In your case, I think powering on the machine to disable Auto Boot would do more damage than it prevents. I agree, skip this step and be prepared to disconnect the battery quickly if the laptop automatically powers on. Good luck!

    Jeff Suovanen -

    Thats right! You don't want power running while working on your logic board.

    Dan -

    This did not work when running High Sierra.

    Kyle B - 답글

    Tried this on a 2018 MBP 13” Touchbar (there’s no iFixit guide for this model yet). Need to replace a broken screen.

    Luckily I managed to connect to an external screen (Cmd-Down Brightness to switch displays) and enter above command. Seems to work, but there’s another problem with this model - it powers up as soon as any key is pressed……. ffs <gnashes teeth>

    Cool_Breeze - 답글

    I unscrew the battery first and wrap electrical tape over the logic board battery connector before attempting any repairs to the board. Haven’t had any problems yet and I’ve worked on about 10 of these models already. Also when you open the bottom case use a suction cup at the bottom and pull up then run a plastic spudger along the edges to disconnect the clips. Also only use a plastic spudger on the board. Saw a youtube video from a repair shop and he did not disconnect the power and used all metal tools during the entire process of removing the board. His last step was to disconnect the battery terminal.

    Brian - 답글

    Is this step necessary if my mac can turn on? Battery fully dead(

    Nursat b - 답글

    BEFORE YOU START: The included torx head stripped off before I was done (and you might need an additional T4) so stop now and go buy a good one. Also they fail to warn you above to get some blue threadlocker ahead of time.

    Jason Sherron - 답글

    This command did not work for me and I read that sometime in later 2020 Apple stopped this command from working…any ideas on a work around?

    Patrick Machacek - 답글

    Not able to do that with damaged screen

    richardjgreen - 답글

    If you have a damaged screen you can still use a converter from thunderbolt (USB 3) to HDMI and plug your Macbook Pro to your TV as monitor display. Just make sure to chose the right Source (HDMI IN) in your TV. I did it and to make it work I unplug and plug again in my Macbook and so I could disable the Auto boot

    Roberto Sanchez Bustos -

    Hi. This does not work on 2018 13” MacBook Pro with Touch Bar. I did exactly this to disable auto boot. But when I check by using nvram -p it says: auto-boot true. Am I doing something incorrectly? I did everything step by step. Copied and pasted the sudo command, pressed enter and then entered my password. I have Big Sur 11.1 installed. Is there any other way since I need to replace the screen. Thank you. Adrian

    Adrian Vizik - 답글

    Hi everyone. This is also a little pointless if you can’t see anything on the screen, and you don’t have a display adapter to USB C to display it. I agree with Brian about removing the back and disconnecting the battery cable before you even think about opening the lid of the MacBook. Applying the insulation tape is also a handy little tip that just makes sure there is no way to discharge from either the board or battery.

    Roberto Enrieu - 답글

    running `nvram -p | grep 'AutoBoot'` in terminal verifies that it was accepted

    result: `AutoBoot %00`

    Marek Polák - 답글

    Running Big Sur 11.6.7 on a 2019 16" MBP, it's "auto-boot". So it's: nvram -p | grep 'auto-boot' to display the current state, the default is true - and then to change it, sudo nvram auto-boot=false which turns it off.

    Ed Mechem -

    This step is completely unnecessary if you follow the guide to disconnect the battery properly. Just put some tape between the battery and logic board connection to prevent it from accidentally touching and therefore powering on the laptop.

    Grant Ormsby - 답글

    It took me a few tries to make this command work, as I was able to copy and paste the command into Terminal, but could not type in my laptop’s password. I finally typed my password into a text document, copied it (command C), and then pasted it into Terminal and it worked.

    tommy404 - 답글

    I didn’t do this. Mine never auto-booted before I replaced the battery. Now it does.

    hatuxka - 답글

    BEFORE YOU DO ANYTHING - CHECK THE BATTERY!

    I-fixit sent me a bad battery, which I didn’t realize until it was already install. They sent me a new one, but I wasted hours uninstalling and reinstalled.

    Get a volt meter and measure the voltage on the output of the battery pack. If it reads 0 V, SEND IT BACK. It should read over 2 V.

    bcardanha - 답글

    I've just received my replacement battery and it reads 0,042V between the two main connectors. Do you think it's dead?

    peter sussex -

    When I did this from Terminal.app within Recovery Mode, the “sudo” was not recognized but I could invoke it without the sudo part. It seems to have been accepted when looking at “nvram -p”

    johann beda - 답글

    When in Recovery Mode, you already have superuser powers. So you don't need to prefix commands with the sudo command to invoke them with root privileges; you already have them. Do a pwd (print working directory) after opening Terminal in Recovery Mode, and you'll see that you're in the root user's directory.

    Ed Mechem -

    I received the battery kit for my 2018 MacBook Pro and as per the above comment from bcardanha - Oct 12, 2021, I checked the voltage on the pads marked + and - . It was zero volts so I panicked a bit.

    I sent a message on the iFixiT Facebook page and I got no reply. I finally found the customer service email for Ifixit Europe and sent them an email voicing my concern as I was not keen to work for couple of hours just to discover that the battery is faulty. I had an almost instant reply on the email (kudos to them) and they adviced me to go ahead and install the new battery as the voltage measured when battery is not connected is not relevant.

    I took a leap of faith and after two hours… the new battery showed 50% charge and everything seems to be working just fine. I am happy it worked.

    Mircea Comanici - 답글

    After removing the old battery and installing the new battery I powered up the MBP before screwing the bottom on. I discovered the my keyboard would not function. It took a few hours of investigation and frustration that I discovered the track pad power ribbon had become partially dislodged from the trackpad. I was able to see that this through the little machined slot where the battery sat. I had to remove the trackpad to reinsert the power ribbon back into the connector in the trackpad. after reassembling and reinstalling the battery etc the keyboard worked. Just food for thought if your run into the keyboard issue.

    Ed Mease - 답글

    This should be the default. IMO I tell you to power on - not the lid.

    G Sena - 답글

    Est ce que cela fonctionne sur un macbook pro 2017 sans touchbar ?

    maël muzelet - 답글

    Bonjour Maël, oui, ce tutoriel concerne "les MacBook Pro 2016 (et plus récents) et les MacBook Retina 12" 2017 (et plus récents)"

    Claire Miesch -

    Excellent instructions. I was able to follow and install the new screen. I recommend that you get a good set of tools before you begin. I started with an inexpensive repair kit bought online. The Penta and torx bits failed. I bought an IFIXIT kit with quality bits and I was able to do everything I needed.

    Tom Markham - 답글

    If you're not running an admin account the sudo command won't work (which honestly, you should not be running admin). Rather than logging in to your admin amount via the OS, in the terminal type "login [admin username]," then the password and you'll be able to do the sudo command as described above. Once you're complete, type "logout [admin username]" and you'll be good to go. Obviously replace [admin username] with whatever the account name for your admin user is.

    arichard2401 - 답글

    For those unable to complete this step because the screen is too damaged I recommend leaving your macbook on until the battery dies.

    Nicholas R Licato - 답글

    Just replaced my 2018 15" MBP battery. Running Sonoma.
    I found no way to disable AutoBoot (The status can be checked in the Power section of system report).

    Anyway, i left my battery completely drain before opening the MBP, and had no issues during the process.

    Cédric Bontems - 답글

    After sending this command in terminal when I checked what happens if I now open the lid, instead the screen lit slightly up (still black) then a battery symbol showing the charging state showed up.

    Now, after replacement of the battery, this is all I get to see.

    No reset of NVRAM nor PRAM helped.

    Currently the new battery charges (58% atm) and it feels like it‘s mocking me.

    webrockers - 답글

    I suspected the keyboard or TouchID sensor wouldn’t work, so I went on and checked every connector.

    I missed connecting the left TouchID sensor from step 31.

    webrockers -

  2. MacBook Pro 13" Touch Bar 2017 스크린 교체, Pentalobe/별나사 풀기: 2 단계, 이미지 1/1
    이 단계에 사용된 도구:
    Magnetic Project Mat
    $19.95
    구매
    • 계속하기 전에 MacBook 플러그를 뽑고 전원을 끄세요. 디스플레이를 닫고 부드러운 표면 위에 뒤집어 놓으세요.

    • P5 Pentalobe/별나사 드라이버를 사용하여 하단 케이스를 고정하는 나사 여섯 개를 풀어주세요:

    • 6.2mm 나사 두 개

    • 3.4mm 나사 네 개

    • 이 수리를 하는 동안, 각 나사를 기억하고 기기 손상을 방지하기 위해 원래 위치로 정확히 돌아가는 것을 확인하세요.

    Sur le mien A1708 EMC3164 j’ai 4 vis de 6,2 (les coins) et 2 vis de 3,4 celles au milieu en bas

    Olivier Cecillon - 답글

    Ce tutoriel n’est pas dans la bonne section !

    c’est le 13” avec touch bar et non celui avec les touches de fonction .

    l’autre tuto nommé “écran complet” est le bon

    Vincent Morault - 답글

    Bonjour Vincent,

    Si vous cherchez le même tutoriel pour le MacBook 13” non Touch Bar, le voici : https://fr.ifixit.com/Tutoriel/Remplacem...

    Claire Miesch -

    Before you start I suggest you get magnifier eyeware as screws and connectors are very small and good lightning are a big PLUS

    Gilles Vigeral - 답글

    Completed whole steps in over 4 hours….but worth it. Works back perfect and battery error message is gone….

    Gilles Vigeral - 답글

    Nothing beats a properly grounded ESD workstation, and a grounded wrist strap.

    Robin Ray - 답글

  3. MacBook Pro 13" Touch Bar 2017 스크린 교체, 흡입 컵을 사용하여 틈 만들기: 3 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체, 흡입 컵을 사용하여 틈 만들기: 3 단계, 이미지 2/2
    • MacBook Pro 전면-중앙 근처 하단 케이스에 흡입 핸들을 사용하세요.

    • 흡입 핸들을 들어 올려 하단 케이스와 섀시사이에 약간의 틈을 만드세요.

  4. MacBook Pro 13" Touch Bar 2017 스크린 교체, 클립 풀기: 4 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 클립 풀기: 4 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 클립 풀기: 4 단계, 이미지 3/3
    • 여는 픽의 한쪽 모서리를 하단 케이스와 섀시사이의 틈에 넣으세요.

    • 여는 픽의 한쪽 모서리를 하단 케이스와 섀시사이의 틈에 넣으세요.

    • 이렇게 하면 하단 케이스를 섀시에 고정하는 첫 번째 숨겨진 클립이 풀립니다. 클립이 풀리는 것을 느끼고 풀리는 소리도 들려야 합니다.

    The instruction implies that sliding the pick up to the side of the case releases the clip. This is far from the truth; it takes a pretty strong force to pop the clip open. The plastic pick is a good start, but you need to reach in and pull the middle of that side of the case pretty hard.

    dkraemer2 - 답글

  5. MacBook Pro 13" Touch Bar 2017 스크린 교체: 5 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 5 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 5 단계, 이미지 3/3
    • 맞은편에 이전 단계를 반복하여 여는 픽을 하단 케이스 밑에서 측면 위로 밀어서 두 번째 클립을 풀어주세요.

  6. MacBook Pro 13" Touch Bar 2017 스크린 교체: 6 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 6 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 6 단계, 이미지 3/3
    • 가장 중앙에 위치한 나사 구멍 두 개 중 하나 근처 하단 케이스 전면 가장자리 밑으로 여는 픽을 다시 한 번 넣으세요.

    • 픽을 단단히 비틀어 하단 케이스를 섀시에 고정하는 세 번째 클립이 풀리도록 하세요.

    • 맞은편의 가장 중앙에 위치한 나사 구멍 두 개 근처에 이 절차를 반복하여 네 번째 클립을 풀어주세요.

    Look at Step 8 pics 2 and 3 to see exactly where the clips are that need to be released. Taking the bottom cover off my MBP took for ever because I didn’t realize the clips were not right around the edges as the wording suggests. Once I realized this, it came off quickly and easily.

    Troy Reimche - 답글

  7. MacBook Pro 13" Touch Bar 2017 스크린 교체: 7 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 7 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 7 단계, 이미지 3/3
    • 하단 케이스를 MacBook 전면을 향해 단단히 당겨 (힌지 부분에서 멀리) 하단 케이스를 고정하는 마지막 클립을 풀어주세요.

    • 한쪽 모서리를 먼저 당긴 다음 다른 모서리를 당기세요

    • 옆으로 당기세요—위로 말고.

    • 이 작업은 많은 힘이 필요할 수 있습니다.

    On the 2018 model, there are two more clips that need to be popped on the sides in the middle. Then it slides out easily.

    Cool_Breeze - 답글

  8. MacBook Pro 13" Touch Bar 2017 스크린 교체, 하단 케이스 분리하기: 8 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 하단 케이스 분리하기: 8 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 하단 케이스 분리하기: 8 단계, 이미지 3/3
    • 하단 케이스를 분리하세요.

    • 하단 케이스를 다시 설치하려면:

    • 디스플레이 힌지 근처 슬라이딩 클립을 제자리에 맞추고 정렬하세요. 커버를 아래로 누르고 힌지를 향해 미세요. 클립이 맞물리면 미끄러짐은 멈춰야 합니다.

    • 슬라이딩 클립이 완전히 맞물리고 하단 케이스가 올바르게 정렬된 것처럼 보이면, 하단 케이스를 단단히 눌러 아래에있는 숨어있는 클립 네 개를 맞물리세요. 그들이 제자리에 끼워지는 것이 느껴지며 소리가 들려야 합니다.

  9. MacBook Pro 13" Touch Bar 2017 스크린 교체, 배터리 커넥터 드러내기: 9 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체, 배터리 커넥터 드러내기: 9 단계, 이미지 2/2
    • 배터리와 가장 가까운 로직 보드 가장자리에서 배터리 커넥터를 덮고있는 큰 테이프를 조심히 벗기세요.

    • 테이프를 떼어내세요.

    Please be VERY careful, I torn up my battery cable and had to replace all the battery.

    Emmanuel Neff - 답글

    Apple worked on my computer and did not put the tape back. I'm assuming it's not important?

    ronfrank - 답글

  10. MacBook Pro 13" Touch Bar 2017 스크린 교체: 10 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 10 단계, 이미지 2/2
    • 배터리 보드 데이터 케이블 커넥터를 덮고있는 작은 테이프 조각을 조심히 떼어내세요.

    • 테이프는 리본 케이블과 통합되어 있으며 완전히 분리되지 않습니다. 커넥터에 접근할 수 있을 만큼만 젖히세요.

    While the tape in this step was definitely attached to the ribbon cable, I accidentally pulled it off during Step 9, thinking that it was a tab to remove the larger tape covering the whole battery connector. It didn’t seem to do any harm.

    cdowney - 답글

  11. MacBook Pro 13" Touch Bar 2017 스크린 교체: 11 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 11 단계, 이미지 2/2
    • Spudger/스퍼저의 끝을 사용하여 케이블을 커넥터에 고정하는 작은 검정색 잠금 탭을 위로 젖히세요.

    Be very careful here. I had to repeat this procedure several times on my MacBook Pro to replace faulty monitors. Eventually, after being opened and closed so many times, the small black locking tab came right off of the connector. Now my battery connection is broken and I can only use my MacBook when it is plugged into the power supply. I’m trying to find a way to securely connect the battery cable without this little locking tab (maybe with tape or something), but so far no luck. Does anyone at iFixit have any advice for me?

    Jamie Near - 답글

    Like Jamie said, use mass amounts of caution here. The lever is very fragile, and mine came off as well - and I’m not exactly a muscular guy. Without it, the connection cannot be made to the data connector, and the computer will not think that a battery is installed. I had to finagle my connector with tweezers and a spudger back into place (and the picture above makes it look normal sized. The picture lies. It is TINY! We’re talking smaller than a small eyelash tiny), and then used some of the adhesive battery strip to hopefully keep it in place.

    Wayne Linder - 답글

    The previous comments are not exaggerated. There ain’t NOTHIN’ to that locking bar. I found it helpful to zoom in with my phone to work on it. It really requires no force to move, I imagine the tape is there to hold it down.

    William Brittain - 답글

  12. MacBook Pro 13" Touch Bar 2017 스크린 교체: 12 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 12 단계, 이미지 2/2
    • 배터리 보드 데이터 케이블을 소켓에서 밀어내세요.

    • 케이블 방향으로 로직 보드와 평행하게 밀어주세요.

  13. MacBook Pro 13" Touch Bar 2017 스크린 교체: 13 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 13 단계, 이미지 2/2
    • 배터리 보드 데이터 케이블을 옆으로 접어서 치우세요.

    The cable is held down with adhesive. Be very gentle with the delicate cable as you peel it back.

    dkraemer2 - 답글

  14. MacBook Pro 13" Touch Bar 2017 스크린 교체: 14 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 14 단계, 이미지 2/2
    • T5 Torx/톡스 드라이버를 사용하여 배터리 전원 커넥터를 고정하는 3.7mm 팬케이크 나사를 풀어주세요.

    Why is my screwdriver not turning even when I have the correct screwdriver and the screw is not stripped

    Jia Liu - 답글

  15. MacBook Pro 13" Touch Bar 2017 스크린 교체, 배터리 분리하기: 15 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체, 배터리 분리하기: 15 단계, 이미지 2/2
    • Spudger/스퍼저를 사용하여 배터리 전원 커넥터를 살살 들어 올려 배터리를 분리하세요.

    • 커넥터가 소켓에서 떨어져 있도록 충분히 높이 들어 올리세요. 수리 도중 실수로 접촉하면 MacBook Pro를 손상할 수 있습니다.

    Dies ist kein Stecker sondern eine Kontaktplatte, die nur leicht angehoben werden muss. Dann am besten mit etwas Tesafilm isolieren.

    SchroedersKater - 답글

    (Translation for myself and others; Thanks for the nice tip by the way!) This is not a plug but a contact plate that only needs to be lifted slightly. Then it is best to isolate with some scotch tape.

    S Woo -

  16. MacBook Pro 13" Touch Bar 2017 스크린 교체, 안테나 케이블 어셈블리: 16 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 안테나 케이블 어셈블리: 16 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 안테나 케이블 어셈블리: 16 단계, 이미지 3/3
    • 플라스틱 커버를 디스플레이 상단 힌지에 고정하는 T3 Torx/톡스 나사 네 개를 풀어주세요.

    • 플라스틱 힌지 커버 두 개를 분리하세요.

  17. MacBook Pro 13" Touch Bar 2017 스크린 교체: 17 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 17 단계, 이미지 2/2
    • 메인 디스플레이 케이블 상단에 알루미늄 커버를 고정하는 2.9mm T3 Torx/톡스 나사 두 개를 풀어주세요.

    • 커버를 분리하세요.

    These are T4 screws on A1706 EMC 3163

    Rex Juggler - 답글

  18. MacBook Pro 13" Touch Bar 2017 스크린 교체: 18 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 18 단계, 이미지 2/2
    • 디스플레이 케이블 플렉스 커넥터 상단에 알루미늄 커버를 고정하는 1.7mm T3 Torx/톡스 나사 두 개를 풀어주세요.

    • 커버를 분리하세요.

  19. MacBook Pro 13" Touch Bar 2017 스크린 교체: 19 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 19 단계, 이미지 2/2
    • 디스플레이 보드 플렉스 케이블을 소켓에서 똑바로 들어 올려 디스플레이 보드에서 분리하세요.

  20. MacBook Pro 13" Touch Bar 2017 스크린 교체: 20 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 20 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 20 단계, 이미지 3/3
    • 디스플레이 케이블 커넥터 상단에 알루미늄 커버 두 개를 고정하는 1.5mm T3 Torx/톡스 나사 네 개를 풀어주세요.

    • 핀셋을 사용하여 알루미늄 커버 두 개를 분리하세요.

    When re-installing the display, be careful to make sure that the display cable from the logic board sits properly ABOVE its connector on the display hinge.

    dkraemer2 - 답글

    What is the exact size of these screws? lost one trying to put it back in and trying to figure out what I need to buy

    laughing rice - 답글

    Step 20….those are T4 Torx screws, not T3.

    scott - 답글

    Is this step necessary? actually i did it, but when installing the new screen, i found the 2 aluminum covers already in the new screen, so i installed the new one without taking them out…

    after it worked, i believe we can skip this step.

    my laptop is 2017 15”, 1707

    Ghannam Adham - 답글

    Isn't it better to remove these two covers during reassembly to have less friction?

    Ludovic - 답글

  21. MacBook Pro 13" Touch Bar 2017 스크린 교체: 21 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 21 단계, 이미지 2/2
    • 안테나 케이블 어셈블리를 고정하는 3.9mm T5 Torx/톡스 나사 네 개를 풀어주세요 (양쪽에 두 개씩).

    • 또한 1.1mm P2 pentalobe/펜타로브/별나사 열 두개를 풀어주세요 (양쪽에 여섯 개씩).

    The 1,1mm screws are completly stuck, I have the screwdrivers but the screws are just not turning. Any tips how to take them off ?

    I tried other screwdrivrer and put a rubber on it while trying to take it off but nothing works,

    Gerard Soprani - 답글

    Had the same problem with my ‘quality’ P2 screwdriver. A dirt cheap set from Ya Xun, nr. YX-6025 saved the day

    Niels Beijer - 답글

    I found that a form downward pressure and gentle slowly increasing rotational pressure consistently worked

    david - 답글

    The 1.1 screws are at a slight angle (on the 2018 model, not sure about the 2017 one) so make sure you angle your screwdriver around 10° off vertical towards the rear edge of the machine.

    Cool_Breeze - 답글

    Stripped a number of these with two different repair kit screwdrivers (other brands). Waiting on a 3rd screwdriver to arrive and then will resort to super glue or a dremel to fit a tool to these and remove. Terrible time with this.

    ajdixon91 - 답글

    Just removing four LCD screen’s now. This is the worst part by far. I have what I thought was a reasonable quality Baku BK-338 P2 Pentalobe screwdriver. I am onto the third display removal and the WiFi antenna removal is where the fun begins. On the first two WiFi antenna, about five (too depressed to count them) screws rounded out in the pentalobe head. I managed to get them all out using flush cutters - gripping them with the cutters as flush as I could to the surface of the antenna and just trying to get them to rotate CCW a little to “break the seal“ so to speak without cutting in so deep as to totally mangle the head and locking them in even tighter :)

    Peter Newman - 답글

    Then I pushed them tangentially with one arm of some stout tweezers and slowly worked them out. Got them all out with minimal damage to the brass part of the antenna but I am confident it will still function OK. On the third one now and four rounded out so I better get back to it. A totally s**t way to attach them and far too many screws IMO. My biggest tip is using a quality tool like the Wera or Wira brands, pushing down into the screw and carefully and slowly applying rotation force. Have some flush cutters on standby in case you round any screws out and good luck.

    Peter Newman - 답글

    F# Apple for making pentalobe screws and f# them for using this many.

    Patrick Simons - 답글

    Wiha calls the P2 driver a 1PL

    maccentric - 답글

    Pay attention: in both sides the two 3,9 mm T5 Torx screws they are different from each other.

    DO NOT mix then otherwise you will won’t be able to install then again correctly.

    Manuel Da Silva - 답글

    Wiha 1PL worked perfectly. the 2PL was too big.

    Robin Ray - 답글

  22. MacBook Pro 13" Touch Bar 2017 스크린 교체: 22 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 22 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 22 단계, 이미지 3/3
    • 안테나 동축 케이블 세 개를 로직 보드에서 똑바로 들어 올려 조심히 분리하세요.

    • 핀셋이나 spudge/스퍼저의 평평한 끝을 각 케이블 아랫면에 넣어 소켓 근처까지 밀고, 살살 비틀거나 들어 올려 분리하세요.

    • 각 케이블을 다시 연결하려면, 커넥터를 소켓 바로 위에 맞춘 다음 아래로 눌러 제자리에 들어가도록 아래로 누르세요.

    A good check that the antenna cables are connected properly, is to gently wiggle the wire. The connector will move back and forth without disconnecting. If you press too hard when reconnecting, the soft brass can become damaged, and you'll need a new antenna bar.

    Robin Ray - 답글

  23. MacBook Pro 13" Touch Bar 2017 스크린 교체: 23 단계, 이미지 1/1
    • 안테나 동축 케이블 세 개를 메인 보드에 고정하는 2.8mm T5 Torx/톡스 나사를 풀어주세요.

  24. MacBook Pro 13" Touch Bar 2017 스크린 교체: 24 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 24 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체: 24 단계, 이미지 3/3
    • 여는 픽을 사용하여 표시된 부분에서 안테나 케이블 어셈블리를 꺼내세요.

    • 디스플레이 케이블 두 개가 손상될 수 있으므로 여는 픽은 좌우로 밀지 마세요.

  25. MacBook Pro 13" Touch Bar 2017 스크린 교체: 25 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체: 25 단계, 이미지 2/2
    • 열 관 아랫면에서 나오는 안테나 케이블 번들을 넣는 동시에 안테나 어셈블리를 조심히 분리하세요.

    Reversing this step was the hardest part for me. There is a small “tunnel” that runs under the heat pipe which the 3 antenna cables plus the securing bracket must be threaded through. The shortest cable easily got stuck or pushed off to the side under the heat pipe. After many attempts, I found success by bending the 3 wires ever so slightly to the left before inserting them in the tunnel, so that when they make it through the tunnel, they were more prone to stay straight. It was easy to grab them one by one with tweezers by doing that. Just have to be very careful.

    cdowney - 답글

    To easily fit the antenna cables – turn the whole antenna assembly about 90 degrees ccw and wiggle it a bit back and forth. Since the cables are a bit prebent they quite easily “pops” up – no need to tie them together. The last trick is to not forget the metal tab – using tweezers or a spudger to help guide the tab in position.

    John Ross - 답글

    I was very nervous about reversing this step (2016 model) but had very little trouble getting the wires back through the channel (only took me a couple minutes). I had a harder time reconnecting them, but did manage that as well.

    ronfrank - 답글

  26. MacBook Pro 13" Touch Bar 2017 스크린 교체: 26 단계, 이미지 1/1
    • 안테나 케이블 어셈블리를 분리하세요.

    • 재조립하는 동안 케이블 번들을 조심히 집어서 열 관 아래 보드의 올바른 위치로 안내하세요. 필요한 경우 도구를 사용하여 안내 도움을 받되 억지로 하지는 마세요.

    I had a LOT of trouble re-installing the three antenna cables underneath the heat pipe! The only way I could get them through was to use clear tape to bind the three antenna connectors together tightly into one pointy end. I was able to push that through into place, but I was not able to push the three separate wires through.

    dkraemer2 - 답글

    It’s possible to avoid this problem by just not removing the antenna assembly entirely. I secured the three cables and the screw holder together with a small cable tie to avoid them slipping out. You can fit the new screen without removing the assembly completely.

    Stuart Mc -

    Thanks dkraermer2 for that tip of wrapping all 3 wires into a narrow point. I used Capton tape. The metal screw holder needed help as it catches on a ridge in the MB. I used tweezers to “Lift” it over that last ridge.

    Macrepair SF - 답글

    Make sure the antenna cable assembly locates correctly on reassembly. It is important to install this down onto its locating lugs, not pushing from the rear of the machine towards the front. There is a small ‘u’ shaped cutout on bottom of the assembly and a metal tab which must locate into the corresponding ‘u’ shaped lug and slot cut into the metal of the top case. If this is not located correctly there is a good chance that the screen will foul when opening and closing resulting in an audible click as it catches the antenna assembly.

    BrianS - 답글

    +1 for BrianS comment. The U shape is a placeholder for the antenna and is located at antenna center. If this ever happened to you, fold gently the antenna strip to leave 3 mm space from the antenna main block, and place the antenna center first in oder for the antenna to fit into the U shape properly.

    Xavier Fischer -

    +1 to both BrianS and Xavier Fischer’s comments above. Even when the lug and the cutout are identified, it’s not easy to tell if it’s been seated correctly until you test the hinge. I found Xavier’s suggestion worked.

    Stuart Mc -

    Putting the three antenna cables to snap onto the connectors again, It felt like I succeeded after much struggle. But after putting it all together - the screen is black. External monitor works though. 2 of 3 feels certain though as it seems on place.

    Martin Klasson - 답글

    Once all 16 antenna screws are removed along with single screw securing wifi simply loosen the antenna and while holding each end , ROTATE it and pull away gently so as to not disturb the bend of the wifi wires passing thru the heat pipe. The wires are never physically touched and they keep their “natural” bend. To reassemble, holding antenna, guide the two wi-fi wires and the securing lug thru heat pipe as the antenna is rotated into place . There is a very narrow milled slot on the underside that the antennas metal shield must fit into or else it will cause the snapping clicking noise ( spoken of earlier in this guide )as the display assembly hangs up during its opening / closing. Make sure if need be, the spacing between the metal shield and plastic body of antenna is the same as the ridge between the milled slot and the milled out area moving towards rear of palm rest. Alignment is important.

    robert - 답글

    I was able to install the new screen without removing the antenna cables, I just loosen the antenna screw and uplift the antenna enough to get the screen cables out and reinserted new cable underneath, a helper might come handy while you install new screen.

    Abid Khan - 답글

  27. MacBook Pro 13" Touch Bar 2017 스크린 교체, 디스플레이 케이블 어셈블리 풀기: 27 단계, 이미지 1/1
    • 디스플레이 케이블 커버 스프링 두 개를 고정하는 3.9mm Torx/톡스 나사 네 개를 풀어주세요.

    Step 27. These are T4 Torx screws, not T3 Torx. FYI

    scott - 답글

  28. MacBook Pro 13" Touch Bar 2017 스크린 교체, 디스플레이 케이블 어셈블리 분리: 28 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 디스플레이 케이블 어셈블리 분리: 28 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 디스플레이 케이블 어셈블리 분리: 28 단계, 이미지 3/3
    • 디스플레이 케이블 어셈블리 왼편을 잡고 MacBook 하단 끝을 향해 당겨서 커버 스프링에서 멀게 하세요.

    • 핀셋을 사용하여 디스플레이 케이블 커버 스프링을 홈에서 당겨 빼세요.

    • 디스플레이 케이블 어셈블리 오른편 커버 스프링에 이 단계를 반복하세요.

    When placing back the holder for the display cable I used the wrong length screws and the bolts connected to the connector strip came off. Is this a concern as I am having back light issues in that I can see the outline of an image but its very dim. Thank you.

    David Moheban - 답글

  29. MacBook Pro 13" Touch Bar 2017 스크린 교체, 힌지 볼트 풀기: 29 단계, 이미지 1/2 MacBook Pro 13" Touch Bar 2017 스크린 교체, 힌지 볼트 풀기: 29 단계, 이미지 2/2
    • 스크린을 완전히 열고 MacBook Pro를 한편으로 세우세요.

    • 한 손으로 MacBook Pro를 잡고, 하단 디스플레이 힌지에서 T8 Torx/톡스 나사 세 개를 풀어주세요.

    • 상단 디스플레이 브래킷에서 나머지 T8 Torx/톡스 나사 세 개를 제거합니다.

  30. MacBook Pro 13" Touch Bar 2017 스크린 교체, 디스플레이 어셈블리 분리: 30 단계, 이미지 1/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 디스플레이 어셈블리 분리: 30 단계, 이미지 2/3 MacBook Pro 13" Touch Bar 2017 스크린 교체, 디스플레이 어셈블리 분리: 30 단계, 이미지 3/3
    • MacBook Pro 스크린과 본체를 단단히 잡으세요. 이 단계에서 어느 쪽이든 예기치 않게 떨어질 수 있습니다.

    • 힌지 브래킷을 섀시의 홈에서 들어 올릴 수 있도록 MacBook Pro 양 절반을 함께 밀어주세요.

    • MacBook Pro 스크린은 귀하를 향해 당기면서 본체는 귀하에서 멀게 밀어 분리하세요.

    • 케이블에 걸리지 않도록 주의하면서 디스플레이/스크린 어셈블리를 분리하세요.

결론

새 교체 부품을 원래 부품과 비교하세요—설치하기 전에 나머지 부품을 옮기거나 새 부품에서 접착 뒷면을 제거해야 할 수 있습니다.

기기를 재조립하려면, 위의 단계들을 역순으로 따르세요.

전자 폐기물을 R2 또는 e-Stewards 인증 재활용 센터로 가져가세요.

수리가 계획대로 진행되지 않았습니까? 기본 문제 해결 또는 자사의

답변 커뮤니티에서 도움을 검색하세요.

다른 82명이 해당 안내서를 완성하였습니다.

다음 번역가들에게 특별히 감사 드립니다:

en ko

100%

Christian Kim님은 저희가 세상을 수리하는데 동참하신 분입니다! 기여하시겠습니까?
번역 시작하기 ›

Nicholas H. of Experimac

회원 가입일: 03/13/18

2,112 평판

안내서 2개 작성하였습니다

댓글 33개

What is the ribbon cable that you must remove before disconnecting the battery do?

Max4r - 답글

your mom.

all joking aside, its the communication between the logic board and the battery controller (cycle count, battery health etc)

Joe Jankins -

What is the exact P2 bit you need to remove the 12 screws holding the antenna bar? I ordered a P2 bit on Amazon that says it’s 0.8mm P2 bit and it’s too big. Not sure if they shipped me the wrong one or what. Been trying to find out exactly what bit to use and no luck so far.

Tyson Roehrkasse - 답글

Pentalobe P1L from Wiha tools fits perfectly.

Robin Ray -

What about the display ribbon cable ?

I have a bad cable and don’t want to spend 400 on display assy when the cable is available on this site for 25

Robin Bonathan - 답글

Were you able to do this successfully? I am in this exact situation and am having a hard time finding anything on it. Which ribbon cable is needed?

Carson Orchard -

I will be doing this in couple of days.

I have screen and the tools.

Robin Bonathan - 답글

Many thanks to everyone who put this guide together

G Gudeuk - 답글

I need to replace the battery board data cable and cannot find it. Any suggestions?

thank you

faithey

faith schaafsma - 답글

Does anyone know if the iFixit screens for the 2017 model have a longer backlight cable to combat the flexgate issue? or is it just the same as the original.

Connor - 답글

Fantastic guide! Only difference on my MB Pro was that all the T5’s were T4’s. Satisfied knowing Apple didn’t get me for this repair! HaHa!

MÆTHEIS SOL - 답글

Is this guide valid for the 2019 model as well?

manuel.martella - 답글

Followed this to the letter, and now my MacBook won’t power up, charge or anything. I’m devastated - and it was just the screen that was not working before.

Any advice other than the usual resets, etc? I don’t want to think that I wrecked the Logic Board…

Richard Belson - 답글

I had the exact same thing happen and now I dont know what to do.

What happened in your case? was the board totally fried?

Anthony Gasbarro -

When reassembling the screen (hinge), it is better to temporarily tape the ribbon cable to the back of the screen; ensuring the cable and the screen circuit board not to mistakenly be positioned on top of the keyboard or accidentaly fold/squeeze the ribbon cable by the hinge.

I almost ripped the ribbon cable with the middle hinge when trying to put the screen hinge back into its place.

Aryo Pinandito - 답글

Is this also Working for the MacBook Pro 2017 with Touch Bar. In Title there is it called Touchbar but its in Category from Mac Book Pro 2017 FunctionKeys ?

Marco - 답글

I did it but didn’t do the auto boot and now it won’t turn on any idea on how I could fix this

azza_wikid_tunez - 답글

So I replaced my screen. Works perfectly, but my touch bar is not working anymore! It shows everything, but I cannot touch operate it anymore. I guess I didn't damage anything. It's strange… where is the cable connected, so I can check if anything is wrong?

Maarten Leemans - 답글

I have the same issue, and I can’t manually adjust screen brightness anymore.

Waleed Nazhan -

same issue, The brightness setting is no available anymore and the touch function of the TouchBar too.

SAVARY Sebastien -

why does the display replacement for the non touch bar model link to the touch bar one when they are different internally?

kegancforbes - 답글

These steps worked well and I have successfully replaced my screen! My a1706 Touch Bar has one issue - the screen brightness can’t be adjusted any more. Anyone be got any tips? I can’t do it via the display menu either.

Vikram Jain - 답글

Amazing, really appreciate it, you helped me doing a successful installation.

Ghannam Adham - 답글

Thank you for the procedure it’s really clear ! After the replacement, i lost two functions : the setting of the brightness and the touch function of the TouchBar ( it works but there is not action when i touch the TouchBar…even after SMC and NVRAM intialization …). An idea about how to fix this issue ?

SAVARY Sebastien - 답글

Super Tutoriel. Attention faire des photos du MacBook Pro 13 pouce. Car les tapes pour débrancher l’alimentation et l’antenne ne sont pas pareilles.

Florian Bonanno - 답글

The instructions worked to perfection. However, when rebooting to go back to terminal and turn autoboot back on I cannot open any applications at all and the computer is sluggish. So that said I cannot open terminal. What could be the issue?

Jeff Craigmyle - 답글

One thing that I think may be issue for apps not opening is I may possibly have damaged the battery board data cable connector as I completely missed the part about it having a release clip. I have ordered a new one hoping that fixes the issue. If anyone has any other ideas please reply.

Jeff Craigmyle -

The tiny screws on 18 are garbage. I was able to get 1 screw out and the others sorta stripped really easily. Now I have to figure out how to get them off.

QuickTech - 답글

Excellent guide. Thanks for putting this together. My first time doing anything like this but installation was successful.

Jacob Ford - 답글

I am wanting to convert my 2017 MacBook Pro to a headless set up because the screen stopped working and wanted to know if I can keep the antennas connected and just unscrew them when taking the screen off? Or are they connected to the display like in previous models?

Cameron Stone - 답글

This guide is for A1706 MacBook?

cristiano - 답글

A1708 I believe

Daniel Long -

21th step is not T% for emc3164?

M GKL - 답글

댓글 쓰기

조회 통계:

24 시간 전: 47

7일 전: 341

30일 전: 1,696

전체 시간: 184,908