주요 콘텐츠로 건너뛰기

부품

지정된 부품이 없습니다.

  1. Use the flat end of a spudger to pry the left speaker connector up and out of its socket on the logic board. Use the tip of a spudger to pry the right speaker connector up and out of its socket on the logic board
    • Use the flat end of a spudger to pry the left speaker connector up and out of its socket on the logic board.

    • Use the tip of a spudger to pry the right speaker connector up and out of its socket on the logic board

    • Be sure to pry on the cable head, and not on the socket itself. Prying on the socket may cause it to separate from the logic board.

  2. Peel back the tape covering the top of the keyboard ribbon cable connector. Use the flat end of a spudger to flip up the retaining flap on the keyboard ribbon cable ZIF socket. Be sure you are prying up on the hinged retaining flap, not the socket itself.
    • Peel back the tape covering the top of the keyboard ribbon cable connector.

    • Use the flat end of a spudger to flip up the retaining flap on the keyboard ribbon cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

    • Use the flat end of a spudger to push the keyboard ribbon cable out of its socket.

  3. Use the flat end of a spudger to pry the trackpad ribbon cable connector up out of its socket.
    • Use the flat end of a spudger to pry the trackpad ribbon cable connector up out of its socket.

  4. Use the flat end of a spudger to pry the keyboard backlight connector up from its socket on the logic board.
    • Use the flat end of a spudger to pry the keyboard backlight connector up from its socket on the logic board.

  5. PC 노트북 배터리

    큰 전력 향상을 위한 손쉬운 수리.

    지금 장보기

    PC 노트북 배터리

    큰 전력 향상을 위한 손쉬운 수리.

    지금 장보기
  6. Use the tip of a spudger or your fingernail to flip up the retaining flap on the microphone ribbon cable ZIF socket.
    • Use the tip of a spudger or your fingernail to flip up the retaining flap on the microphone ribbon cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

    • Pull the microphone ribbon cable out of its socket.

  7. Use the tip of a spudger to flip up the display data cable lock and rotate it toward the DC-In side of the computer. Pull the display data cable straight out of its socket on the logic board.
    • Use the tip of a spudger to flip up the display data cable lock and rotate it toward the DC-In side of the computer.

    • Pull the display data cable straight out of its socket on the logic board.

    • Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.

  8. Use the flat end of a spudger to carefully pry off the rubber screw cap on the raised screw head near the MagSafe 2 connector.
    • Use the flat end of a spudger to carefully pry off the rubber screw cap on the raised screw head near the MagSafe 2 connector.

  9. Remove the following six screws securing the logic board to to the upper case:
    • Remove the following six screws securing the logic board to to the upper case:

    • One 3.1 mm T5 Torx screw

    • One 2.5 mm T5 Torx screw

    • One 5.5 mm silver, raised-head T5 Torx screw

    • Two 5.7 mm T5 Torx screws

    • One 3.8 mm silver T5 Torx screw

  10. Lifting from the side nearest the battery, rotate the logic board toward the top of the MacBook Pro. You may need to slide the logic board a few millimeters to the left in order to get clearance for the ports along the right edge of the board.
    • Lifting from the side nearest the battery, rotate the logic board toward the top of the MacBook Pro.

    • You may need to slide the logic board a few millimeters to the left in order to get clearance for the ports along the right edge of the board.

    • Using the flat end of a spudger, carefully push the MagSafe 2 connector out of its socket on the bottom of the logic board.

    • Disconnecting the MagSafe 2 connector can be difficult. If you are only removing the logic board to temporarily get it out of the way, such as for a battery replacement, you may find it easier to simply remove the two 2.5 mm T5 Torx screws securing the MagSafe DC-In board, and then remove the logic board and MagSafe board together.

  11. Remove the logic board assembly from the MacBook Pro. When reinstalling the motherboard, make sure all cables are visible and not trapped under the motherboard. Clockwise from top: battery, right speaker, keyboard backlight, AirPort/camera, display, microphone, left speaker, keyboard, and trackpad.
    • Remove the logic board assembly from the MacBook Pro.

    • When reinstalling the motherboard, make sure all cables are visible and not trapped under the motherboard.

    • Clockwise from top: battery, right speaker, keyboard backlight, AirPort/camera, display, microphone, left speaker, keyboard, and trackpad.

결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

Andrew Optimus Goldheart

회원 가입일: 2009년 10월 17일

420,600 평판

안내서 411개 작성하였습니다

iFixit iFixit 회원

Community

99 회원들

안내서 9,289개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 3

지난 30일: 4

전체 시간: 1,038