메인 콘텐츠로 스킵하기

소개

Having wireless (Wi-Fi or Bluetooth) connectivity issues? Use this guide to replace the AirPort board.

  1. Remove the following pentalobe screws securing the lower case to the MacBook Pro:
    • Remove the following pentalobe screws securing the lower case to the MacBook Pro:

    • Eight 3.1 mm

    • Two 2.3 mm

  2. Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro. Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.
    • Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.

  3. The lower case has two plastic pegs (red) that fit into plastic clips in the upper case (orange). During reassembly, gently push down the center of the lower case to reattach the case to its two plastic clips. During reassembly, gently push down the center of the lower case to reattach the case to its two plastic clips.
    • The lower case has two plastic pegs (red) that fit into plastic clips in the upper case (orange).

    • During reassembly, gently push down the center of the lower case to reattach the case to its two plastic clips.

  4. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now
  5. Peel back the sticker covering the battery connector.
    • Peel back the sticker covering the battery connector.

  6. Gently lift each side of the battery connector to pry the connector out of its socket on the logic board. Bend the connector back toward the battery, ensuring that the battery connector doesn't accidentally make contact with the logic board. Bend the connector back toward the battery, ensuring that the battery connector doesn't accidentally make contact with the logic board.
    • Gently lift each side of the battery connector to pry the connector out of its socket on the logic board.

    • Bend the connector back toward the battery, ensuring that the battery connector doesn't accidentally make contact with the logic board.

  7. Disconnect the three airport Antenna cable connectors from their sockets on the AirPort board and bend them up and out of the way. Be careful to pry only against each connector, and not its cable or socket. Be careful to pry only against each connector, and not its cable or socket.
    • Disconnect the three airport Antenna cable connectors from their sockets on the AirPort board and bend them up and out of the way.

    • Be careful to pry only against each connector, and not its cable or socket.

  8. Remove the single 2.9 mm T5 Torx screw securing the AirPort board.
    • Remove the single 2.9 mm T5 Torx screw securing the AirPort board.

  9. Lift the end of the AirPort board up enough to pass over the heat sink directly behind it. Do not lift the AirPort board too high, or you could damage the contacts or socket. Pull the AirPort board straight out of its socket on the logic board.
    • Lift the end of the AirPort board up enough to pass over the heat sink directly behind it.

    • Do not lift the AirPort board too high, or you could damage the contacts or socket.

    • Pull the AirPort board straight out of its socket on the logic board.

    • There is a slightly adhesive thermal pad beneath the AirPort board. Be sure to reapply this when reinstalling the board, or transfer it to your replacement board.

결론

To reassemble your device, follow these instructions in reverse order.

다른 5명이 해당 안내서를 완성하였습니다.

Andrew Optimus Goldheart

회원 가입일: 2009년 10월 17일

417,588 평판

안내서 411개 작성하였습니다

iFixit iFixit 회원

Community

98 회원들

안내서 8,966개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 8

지난 7일: 99

지난 30일: 405

전체 시간: 10,873