MacBook Pro 15" Retina Display Mid 2015 배터리 커넥터 교체

소개

배터리를 분리하지 않고 플러그를 뽑는 선행 작업입니다.

필요한 것

1 단계 배터리 커넥터

MacBook Pro 15" Retina Display Mid 2015 배터리 커넥터 교체, 배터리 커넥터: 1 단계, 이미지 1/1

배터리 커넥터를 덮고 있는 스티커를 벗겨내세요.

번역하기

You only need to remove the tape to the edge of the flap. This is enough to be able to pry the battery connector up.

Aaron Freidus - 2018년 9월 16일 답글

+1 to above comment

Andrew Saunders - 2019년 1월 19일 답글

Note that the photo is taken from the hinge side - the other way to the photo in step 3

Toby Thurston - 2019년 5월 6일 답글

I chanced it, didnt disconnect the battery and all is well even after giving the insides a good vacuuming before changing the SSD.

Dermot O Logical - 2019년 7월 16일 답글

It is just the top layer of tape that you want to lift, you need to seperate it from the bottom layer.

Kelv - 2021년 1월 29일 답글

You don’t actually need to remove the tape or even peel it off at all. Just pull up the battery connector up with the tape still attached.

AJ Lorenzo - 2021년 1월 31일 답글

pay attention that the macbook in this picture is presented the “wrong side”: if you accidentally remove the tape covering the trackpad cable and thereby also take the trackpad cable out of the zif-socket, your keyboard and trackpad won’t work anymore. putting the trackpad cable back into the (tiny) socket will fix the issue though.

sam - 2021년 6월 21일 답글

2 단계

MacBook Pro 15" Retina Display Mid 2015 배터리 커넥터 교체: 2 단계, 이미지 3/3

배터리 커넥터의 양쪽을 조심히 들어 올려 로직 보드의 소켓에서 커넥터를 들어 올려 빼세요.
커넥터를 배터리 쪽으로 다시 구부려 배터리 커넥터가 실수로 로직 보드에 닿지 않도록 주의하세요.

번역하기

why is this necessary to remove a hard drive?

Lawtay - 2018년 5월 24일 답글

@lawrencetaylor On any electronics repair, you need to disconnect all sources of power before you start. It’s a basic safety precaution and also removes the risk of accidentally shorting a connection somewhere (which can potentially kill your MacBook).

Jeff Suovanen - 2018년 5월 28일

I chanced it, didnt disconnect the battery and all is well even after giving the insides a good vacuuming before changing the SSD.

Dermot O Logical - 2019년 7월 16일 답글

Picture doesn’t match the computer. Hard to tell which connector to disconnect

James Mitchell - 2019년 8월 2일 답글

Hi James, are you sure you have the correct guide for your machine? Try using our MacBook Identification tool.

Sam Goldheart - 2019년 8월 22일

Habe den Akkustecker beim putzen abgemacht um keinen Stromschlag zu kriegen, jetzt wieder eingebaut. Nun habe ich folgendes Problem: Akku wird geladen, aber steigt niemals ueber % und manchmal geht er trotz Anschluss an das Stromnetz einfach aus. Hat da jemand eine Idee?

paul - 2019년 8월 27일 답글

I used the identification tool and can confirm what James is seeing. The picture doesn’t match for this step. There is no piece with visible holes punched in it.

Joshua McFarland - 2019년 10월 16일 답글

There is an extra piece of plastic on the connector, you might want to peel that off too. It’s not in the pictures.

Ellie B - 2020년 3월 15일

There is a battery cover with two T5 screws that must be removed before prying on the connector.

Dennis Newton - 2020년 11월 20일 답글

Hi Dennis,

Thanks for bringing this up! I’ll work on verifying this and adjust the guide as needed.

Arthur Shi - 2020년 11월 24일

My battery connector had another layer of plastic on it that I removed first

Kelv - 2021년 1월 29일 답글

For an A1398, the screws on the adjacent cover were T6, not T5; one of the tips in the battery kit was suitable.

Zathras - 2021년 4월 29일 답글

I need dis board hw much

Ebuka Ofodile - 2021년 5월 10일 답글

After separating the battery connector, I took the addd precaution of placing a folded post-it between the connector bank and the socket.

Matt Fisher - 2021년 8월 24일 답글

You can also use a plastic tool to hold back the battery connector. My connector was under the plastic tab and had no screws. You may need to check the build version as there are a number of A1398 versions.

Robin Razzell - 2022년 1월 1일 답글

When you install the new battery, it may look like the holes in the connector need to be slid on to the connector toward the rear of the mac. I tried bending the cable to make it work. This could damage the cables. You really need only push directly downward on the connector, as you pulled up on it to remove it initially. It will pop into place with a little pressure, just make sure it's lined up properly.

Jeffrey Andrews - 2022년 5월 30일 답글

I had to use quite a lot of pressure to make the connector on my new battery pop all the way down. I thought it was down already when it was only half way, as I was afraid to use too much force. Maybe it varies between different battery brands, but just make sure that the connector should go all the way down and not have a gap between the two parts.

Magnus W - 2022년 6월 18일 답글

" …ensuring that the battery connector doesn't accidentally make contact with the logic board."

You appear to assume that everyone knows which item is the logic board. I can attest that not everyone does. Clarity here would be helpful.

Mark - 2022년 7월 8일 답글

If you don't know what the/a logic board is, you probably shouldn't be opening devices.

Art Hackett - 2023년 2월 24일 답글

Art Hackett. Not useful. This guide is for laypeople. Nobody is supposed to know much of anything. That's the point of the guide and the existence of iFixit. You could have used that time to explain what the logic board is for people who are already here anyway.

Anyway onward and upward. If you don't know what a logic board is and you're here. https://www.google.com/search?q=macbook+...

There, now you're an expert like Art.

fixedtit - 2024년 1월 11일 답글