기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

Mad Catz Street Fighter IV FightPad Circuit Board Replacement

소개

Use this as a guide to remove the motherboard so you can access the FightPad's buttons and directional pad.

필요한 것

  1. Mad Catz Street Fighter IV FightPad Circuit Board Replacement, Rear and Side Case: 1 단계, 이미지 1/1

    • Use tweezers to completely remove the sticker from the rear of controller.

    번역하기

  2. Mad Catz Street Fighter IV FightPad Circuit Board Replacement: 2 단계, 이미지 1/1

    • Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.

    번역하기

  3. Mad Catz Street Fighter IV FightPad Circuit Board Replacement: 3 단계, 이미지 1/2 Mad Catz Street Fighter IV FightPad Circuit Board Replacement: 3 단계, 이미지 2/2

    • Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases.

    • Use the plastic opening tool to pry the two cases apart.

    번역하기

  5. Mad Catz Street Fighter IV FightPad Circuit Board Replacement: 4 단계, 이미지 1/2 Mad Catz Street Fighter IV FightPad Circuit Board Replacement: 4 단계, 이미지 2/2

    • Remove the two rubber side grips.

    번역하기

  6. Mad Catz Street Fighter IV FightPad Circuit Board Replacement, RS-DP-LS Switch: 5 단계, 이미지 1/2 Mad Catz Street Fighter IV FightPad Circuit Board Replacement, RS-DP-LS Switch: 5 단계, 이미지 2/2

    • Locate RS-DP-LS switch.

    • Pull upwards on the switch to remove it.

    번역하기

  7. Mad Catz Street Fighter IV FightPad Circuit Board Replacement, Circuit Board: 6 단계, 이미지 1/1

    • Locate the four 8.3 mm Phillips screws on the circuit board and remove them.

    번역하기

  8. Mad Catz Street Fighter IV FightPad Circuit Board Replacement: 7 단계, 이미지 1/3 Mad Catz Street Fighter IV FightPad Circuit Board Replacement: 7 단계, 이미지 2/3 Mad Catz Street Fighter IV FightPad Circuit Board Replacement: 7 단계, 이미지 3/3

    • Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board.

    • Be careful with the wires connected to the circuit board itself as they are thin and delicate.

    • When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 8명과 함께

Jefferson Hsu

회원 가입일: 09/18/12

411 평판

안내서 3개 작성하였습니다

배지: 9

배지 +6개 더

팀

Cal Poly, Team 1-7, Propen Fall 2012 Cal Poly, Team 1-7, Propen Fall 2012 회원

CPSU-PROPEN-F12S1G7

4 회원들

안내서 14개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 2,043