기기를 수리하세요 커뮤니티 상점

이 안내서에는 최근 변경 사항이 더 있습니다. 최신 비검증 버전으로 전환하십시오.

Mad Catz Street Fighter IV FightPad Directional Pad Replacement

소개

Use this as a guide to remove or replace the rubber part of the directional pad.

필요한 것

  1. Mad Catz Street Fighter IV FightPad Directional Pad Replacement, Rear and Side Case: 1 단계, 이미지 1/1

    • Use tweezers to completely remove the sticker from the rear of controller.

    번역하기

  2. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 2 단계, 이미지 1/1

    • Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.

    번역하기

  3. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 3 단계, 이미지 1/2 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 3 단계, 이미지 2/2

    • Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases.

    • Use the plastic opening tool to pry the two cases apart.

    번역하기

  5. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 4 단계, 이미지 1/2 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 4 단계, 이미지 2/2

    • Remove the two rubber side grips.

    번역하기

  6. Mad Catz Street Fighter IV FightPad Directional Pad Replacement, RS-DP-LS Switch: 5 단계, 이미지 1/2 Mad Catz Street Fighter IV FightPad Directional Pad Replacement, RS-DP-LS Switch: 5 단계, 이미지 2/2

    • Locate RS-DP-LS switch.

    • Pull upwards on the switch to remove it.

    번역하기

  7. Mad Catz Street Fighter IV FightPad Directional Pad Replacement, Circuit Board: 6 단계, 이미지 1/1

    • Locate the four 8.3 mm Phillips screws on the circuit board and remove them.

    번역하기

  8. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 7 단계, 이미지 1/3 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 7 단계, 이미지 2/3 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 7 단계, 이미지 3/3

    • Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board.

    • Be careful with the wires connected to the circuit board itself as they are thin and delicate.

    • When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.

    번역하기

  9. Mad Catz Street Fighter IV FightPad Directional Pad Replacement, Directional Pad: 8 단계, 이미지 1/1

    • Use tweezers to remove the rubber part of the directional pad.

    번역하기

  10. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 9 단계, 이미지 1/2 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 9 단계, 이미지 2/2

    • Insert a new directional pad over the original directional pad's location.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 6명과 함께

Jefferson

회원 가입일: 09/26/12

78 평판

안내서 1개 작성함

배지: 7

배지 +4개 더

팀

Cal Poly, Team 1-7, Propen Fall 2012 Cal Poly, Team 1-7, Propen Fall 2012 회원

CPSU-PROPEN-F12S1G7

4 회원들

안내서 14개 작성하였습니다

댓글 2개

mi spiegate l'utilita di questa guida?vendere forse le pinzette e tutte le altre stronzatine che servono per riparare il fightpad?quando invece il pezzo più importante cioè il gommino non lo vendete....fate pena

auredo1988 - 답글

Hi I don't speak Italian but I think you are asking "what is the purpose of this guide?". We made these as a project for university because I wanted to resolder a wire in this controller that came undone. For good measure we made a guide for each individual part although the real purpose of these guides was for the full disassembly and re soldering.

Eric Devlin - 답글

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 1

30일 전: 15

전체 시간: 4,428