소개

Removing the FightPad's front case for replacing the case or front artwork.

Use tweezers to completely remove the sticker from the rear of controller.
  • Use tweezers to completely remove the sticker from the rear of controller.

댓글 쓰기

Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.
  • Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.

댓글 쓰기

Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases. Use the plastic opening tool to pry the two cases apart.
  • Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases.

  • Use the plastic opening tool to pry the two cases apart.

댓글 쓰기

Remove the two rubber side grips. Remove the two rubber side grips.
  • Remove the two rubber side grips.

댓글 쓰기

Mac RAM 키트
Mac 속도를 높이십시오. 메모리를 최대한 활용하십시오.
Mac RAM 키트
Mac에서 메모리를 더 많이 확보하십시오.
Locate RS-DP-LS switch. Pull upwards on the switch to remove it.
  • Locate RS-DP-LS switch.

  • Pull upwards on the switch to remove it.

댓글 쓰기

Locate the four 8.3 mm Phillips screws on the circuit board and remove them.
  • Locate the four 8.3 mm Phillips screws on the circuit board and remove them.

댓글 쓰기

Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board. Be careful with the wires connected to the circuit board itself as they are thin and delicate. When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.
  • Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board.

  • Be careful with the wires connected to the circuit board itself as they are thin and delicate.

  • When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.

댓글 쓰기

Remove the six buttons one by one by gripping the back of each one and pushing on them from the front. Use tweezers to remove the rubber part of the directional pad before you try to remove the shoulder buttons.
  • Remove the six buttons one by one by gripping the back of each one and pushing on them from the front.

  • Use tweezers to remove the rubber part of the directional pad before you try to remove the shoulder buttons.

  • When reinserting the buttons make sure they are in the correct place and oriented correctly.

댓글 쓰기

Remove the left and right shoulder buttons by sliding them out of their respective slots.
  • Remove the left and right shoulder buttons by sliding them out of their respective slots.

댓글 쓰기

Pull the plastic piece out from the bottom of the controller. Pull the plastic piece out from the bottom of the controller.
  • Pull the plastic piece out from the bottom of the controller.

댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Eric

회원 가입일: 2012년 09월 26일

81 평판

안내서 3개 작성하였습니다

Cal Poly, Team 1-7, Propen Fall 2012 Cal Poly, Team 1-7, Propen Fall 2012 회원

CPSU-PROPEN-F12S1G7

4 회원들

안내서 7개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 2

전체 시간: 1,099