주요 콘텐츠로 건너뛰기

소개

Use this guide to replace the charging port in a Microsoft Surface Pro.

  1. Microsoft Surface Pro Charging Port Replacement, Display: 1 단계, 이미지 1/1
    • Use a heated iOpener or a heat gun to heat the edges of the display and soften its adhesive.

    • If you're using an iOpener it may take several cycles of reheating and applying it to soften the adhesive enough. Every time, let the iOpener sit on the display for at least a minute before reheating to allow the adhesive to soften.

  2. Microsoft Surface Pro Charging Port Replacement: 2 단계, 이미지 1/2 Microsoft Surface Pro Charging Port Replacement: 2 단계, 이미지 2/2
    • Apply a suction cup as close as possible to the edge of the display.

    • Use the suction cup to lift the edge of the display enough to insert an opening pick under the edge.

    • Slide the opening pick all the way around the edges of the display to cut through the adhesive on the bezel.

    • Do not insert the opening pick past the bezel of the display—you may permanently damage the display.

    • Be very careful and move slowly during this step. The display is fragile and will crack if too much force is applied against it. If your tools seem stuck, apply more heat to further soften the adhesive.

  3. Microsoft Surface Pro Charging Port Replacement: 3 단계, 이미지 1/2 Microsoft Surface Pro Charging Port Replacement: 3 단계, 이미지 2/2
    • Starting from the top edge, lift the display slightly. If you feel any resistance, use heat and an opening pick to slice through any remaining adhesive.

    • Before completely removing the display, disconnect the three display cables.

  4. Microsoft Surface Pro Charging Port Replacement: 4 단계, 이미지 1/1
    • Remove the display.

  5. Microsoft Surface Pro Charging Port Replacement, Charging Port: 5 단계, 이미지 1/2 Microsoft Surface Pro Charging Port Replacement, Charging Port: 5 단계, 이미지 2/2
    • Using a T5 Torx screwdriver, unscrew a total number of 23 screws located on the outside panel of the Surface Pro.

  6. Microsoft Surface Pro Charging Port Replacement: 6 단계, 이미지 1/1
    • Use the plastic opening tool or fingers to pry out the front camera.

  7. Microsoft Surface Pro Charging Port Replacement: 7 단계, 이미지 1/1
    • Lift the outside panel from the Surface Pro

  8. Microsoft Surface Pro Charging Port Replacement: 8 단계, 이미지 1/2 Microsoft Surface Pro Charging Port Replacement: 8 단계, 이미지 2/2
    • Use the T5 torx screw driver to unscrew the 6 T5 screws in the left and right outside metal panels

    • Use the T2 torx screw driver to unscrew the 23 T2 screws on the left and right outside metal panels

  9. Microsoft Surface Pro Charging Port Replacement: 9 단계, 이미지 1/1
    • Pull out left and right metal panels with hands

  10. Microsoft Surface Pro Charging Port Replacement: 10 단계, 이미지 1/1
    • Pull out the orange charging port strip using tweezers

  11. Microsoft Surface Pro Charging Port Replacement: 11 단계, 이미지 1/1
    • Unscrew the two T5 torx screws located on each side of the charging port.

  12. Microsoft Surface Pro Charging Port Replacement: 12 단계, 이미지 1/1
    • Once you have unscrewed the charging port, you can gently pull it out with your hands.

결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

Jonathan Choi

회원 가입일: 2013년 10월 09일

855 평판

안내서 4개 작성하였습니다

Cal Poly, Team 8-20, Regan Fall 2013 Cal Poly, Team 8-20, Regan Fall 2013 회원

CPSU-REGAN-F13S8G20

4 회원들

안내서 13개 작성하였습니다

댓글 3개

Where do you get a replacement charging port at?

Evil Robot - 답글

Agree where can you get the port?

J-M. M. - 답글

Same instructions for changing the port on a surface pro 2?

Robert - 답글

댓글 쓰기

조회 통계:

24 시간 전: 14

7일 전: 86

30일 전: 336

전체 시간: 23,002