기기를 수리하세요 커뮤니티 상점

Minolta QTsi Maxxum Eyelet Straps Replacement

소개

Replace your broken eyelet strap so that you can wear a strap with your Minolta QTsi Maxxum camera.

필요한 것

  1. Minolta QTsi Maxxum Eyelet Straps Replacement, Eyelet Straps: 1 단계, 이미지 1/1

    • The battery compartment is located on the bottom panel of the camera.

    • Use a coin to open the battery compartment of the camera.

    • Twist the coin counterclockwise in order to release the latch.

    편집

  2. Minolta QTsi Maxxum Eyelet Straps Replacement: 2 단계, 이미지 1/1

    • Once the compartment is open, grab the batteries and pull them out of the compartment.

    • There should be two batteries inside the battery compartment.

    편집

  3. Minolta QTsi Maxxum Eyelet Straps Replacement: 3 단계, 이미지 1/1

    • With a screwdriver, remove the (7) black Phillips #00 5mm screws on the bottom of the camera.

    • The screws are located on the outer edge of the bottom panel.

    • Be careful when removing the screws from the panel because they are easy to lose.

    • Once all the screws are removed, the panel should easily come off.

    편집

  4. Minolta QTsi Maxxum Eyelet Straps Replacement: 4 단계, 이미지 1/1

    • Once the bottom panel is removed, the one screw at the bottom of the battery compartment should be visible.

    • Remove the (1) black Phillips #00 5mm screw from the battery compartment.

    편집

  6. Minolta QTsi Maxxum Eyelet Straps Replacement: 5 단계, 이미지 1/1

    • Press the release button on the side panel to pop open the back piece of the camera.

    편집

  7. Minolta QTsi Maxxum Eyelet Straps Replacement: 6 단계, 이미지 1/1

    • Once the back panel is open, the chamber containing one screw should be visible.

    • Remove the (1) black Phillips #00 5mm screw inside.

    편집

  8. Minolta QTsi Maxxum Eyelet Straps Replacement: 7 단계, 이미지 1/2 Minolta QTsi Maxxum Eyelet Straps Replacement: 7 단계, 이미지 2/2

    • Take out the (2) Phillips #00 5mm screws on the right side panel of the camera.

    • Remove the (1) Phillips #00 5mm screw on the left side panel of the camera.

    • Remove the side panels from the camera and set them aside .

    • Be careful when removing side panels. There is a plastic piece and spring underneath the left side panel that could get lost.

    편집

  9. Minolta QTsi Maxxum Eyelet Straps Replacement: 8 단계, 이미지 1/1

    • When looking at the back of the camera, there should be a single screw on each side of the viewfinder.

    • Remove these (2) silver Phillips #00 5mm screws from each side of the viewfinder.

    편집

  10. Minolta QTsi Maxxum Eyelet Straps Replacement: 9 단계, 이미지 1/1

    • When looking at the top of the camera, the flash hood is visible.

    • Lift the flash hood and remove the (1) silver Phillips #00 5mm screw.

    편집

  11. Minolta QTsi Maxxum Eyelet Straps Replacement: 10 단계, 이미지 1/2 Minolta QTsi Maxxum Eyelet Straps Replacement: 10 단계, 이미지 2/2

    • The top panel of the camera should now be easy to pop off. If it is not, make sure that all screws listed in steps 3-9 are removed.

    • Lift the top panel away from the rest of the camera.

    • Be careful when removing the top panel because there are wires connected to it.

    편집

  12. Minolta QTsi Maxxum Eyelet Straps Replacement: 11 단계, 이미지 1/1

    • Once all parts of the camera are removed, both eyelet straps should be visible on the top left and right sides.

    • Unscrew the (4) black Phillips #00 5mm screws to remove each eyelet strap holder and replace them.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Maya Van Londen

회원 가입일: 10/10/16

315 평판

안내서 2개 작성하였습니다

배지: 12

배지 +9개 더

팀

Sam Houston State, Team 12-4, Blackburne Fall 2016 Sam Houston State, Team 12-4, Blackburne Fall 2016 회원

SHSU-BLACKBURNE-F16S12G4

4 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 6

30일 전: 11

전체 시간: 349