주요 콘텐츠로 건너뛰기

소개

How to remove the cutting head's bottom cover for device service or part replacement in a Mk Diamond Wet Saw MK660 2010.

  1. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade Cover: step 1, image 1 of 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade Cover: step 1, image 2 of 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade Cover: step 1, image 3 of 3
    • Before you begin, make sure to power off and unplug the device from the outlet.

    • If the clear water pump hose is connected, remove it now.

    • Loosen the plastic knob holding the saw's cutting head in place.

    • Lower the cutting head while keeping it steady.

  2. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 2, image 1 of 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 2, image 2 of 2
    • Unscrew the knob.

    • Remove it from the cutting head.

  3. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 3, image 1 of 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 3, image 2 of 2
    • Loosen the plastic knob holding the blade cover in place.

  4. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 4, image 1 of 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 4, image 2 of 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 4, image 3 of 3
    • Loosen the wing nut on the blade cover pivot shaft.

    • Remove the wing nut and accompanying washer.

  5. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 5, image 1 of 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 5, image 2 of 2
    • Pivot the blade cover up and pull it off the shaft.

  6. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade: step 6, image 1 of 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade: step 6, image 2 of 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade: step 6, image 3 of 3
    • Insert the provided spanner wrench into one of the four tightening holes on the inner flange behind the blade.

    • Use the the provided nut wrench to loosen the hex nut while providing counterforce with the spanner wrench.

  7. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 7, image 1 of 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 7, image 2 of 2
    • Remove the hex nut.

    • Remove the outer flange.

  8. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 8, image 1 of 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 8, image 2 of 2
    • Remove the cutting blade.

    • The blade can be sharp, so handle with care.

  9. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Cutting Head: step 9, image 1 of 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Cutting Head: step 9, image 2 of 3 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Cutting Head: step 9, image 3 of 3
    • Pull the entire cutting head straight off the shaft holding it in place.

  10. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Bottom Cover: step 10, image 1 of 1
    • Remove the eight Phillips #2 screws on the underside of the cutting head.

  11. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 11, image 1 of 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: step 11, image 2 of 2
    • Remove the bottom cover.

결론

To reassemble your device, follow these instructions in reverse order.

Carsten Frauenheim

회원 가입일: 2020년 03월 10일

71,693 평판

안내서 330개 작성하였습니다

iFixit iFixit 회원

Community

148 회원들

안내서 15,460개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 90