부품

부품은 필요하지 않습니다.

Objective: remove the rear case from the Motorola Droid X phone.
  • Objective: remove the rear case from the Motorola Droid X phone.

    • This is what the Motorola Droid X looks like before disassembly. In the front, there is a large LCD touch screen.

댓글 쓰기

INSTRUCTION: Turn the phone over so that the back faces up.
  • INSTRUCTION: Turn the phone over so that the back faces up.

댓글 쓰기

  • Objective: remove the battery casing plate.

    • The case plate has a push and slide mechanism.

댓글 쓰기

  • INSTRUCTION 1: Push on the upper side of the casing located under the camera lens.

  • INSTRUCTION 2: Slide down the battery case plate.

댓글 쓰기

  • INSTRUCTION: Insert your finger tips into the edges of the opening and pull the casing off.

댓글 쓰기

  • Objective: remove the battery from the battery compartment.

댓글 쓰기

  • INSTRUCTION: Grab the red tab that says "Battery Release" and slowly lift it up. This will remove the battery.

댓글 쓰기

  • Objective: remove two small black screws from the back of the phone.

    • These two (2) screws help hold the phone together. They need to be removed by a Phillips Hex 2mm screwdriver,

댓글 쓰기

  • INSTRUCTION: Remove two black screws from the back of the phone.

댓글 쓰기

  • Objective: remove the two plastic pieces in front of the phone - they cover the remaining screws.

    • The two plastic pieces are clipped onto the phone as covers. They are located at the top and the bottom of the phone.

댓글 쓰기

  • INSTRUCTION: Flip the phone over to the front side.

댓글 쓰기

  • INSTRUCTION: Use the iFixit tool as a crowbar to pry the top plastic cover piece off of the phone. It will pop off.

댓글 쓰기

  • INSTRUCTION: Use the iFixit tool as a crowbar to pry the bottom plastic piece off the phone.

댓글 쓰기

  • Objective: remove four white screws from the corners of the screen.

    • These four (4) screws help hold the phone together. Use a Phillips Hex 2mm screwdriver

댓글 쓰기

  • INSTRUCTION: remove the 2 white screws from the upper corners of the screen.

댓글 쓰기

  • INSTRUCTION: remove the 2 white screws from the lower corners of the screen.

댓글 쓰기

  • Objective: remove the rear case from the phone in order to provide access to inside the phone.

    • The phone is now held together by the casing alone. You need to pop the two halves apart.

댓글 쓰기

  • INSTRUCTION: Use the iFixit tool like a crowbar to pry apart the front and rear halves of the casing. They will pop apart.

댓글 쓰기

  • Now you are ready to access the internal circuits of the phone.

댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

Anna

회원 가입일: 2012년 10월 08일

25 평판

안내서 1개 작성함

Ohio State, Team 1-1, Voss Fall 2012 Ohio State, Team 1-1, Voss Fall 2012 회원

OSU-VOSS-F12S1G1

3 회원들

안내서 2개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 0

전체 시간: 667