기기를 수리하세요 커뮤니티 상점

Motorola MBP667CONNECT Speaker Replacement

소개

This guide will show users how to take apart the camera housing in order to replace the speaker.

필요한 것

  1. Motorola MBP667CONNECT Speaker Replacement, Camera Stand: 1 단계, 이미지 1/2 Motorola MBP667CONNECT Speaker Replacement, Camera Stand: 1 단계, 이미지 2/2

    • Remove two 5 mm Phillips #1 screws from the bottom of the camera stand.

    편집

  2. Motorola MBP667CONNECT Speaker Replacement: 2 단계, 이미지 1/1

    • Use a nylon spudger to remove the casing.

    편집

  3. Motorola MBP667CONNECT Speaker Replacement: 3 단계, 이미지 1/1

    • Remove the two 5 mm Phillips #1 screws attached to the black plastic under the casing.

    편집

  5. Motorola MBP667CONNECT Speaker Replacement: 4 단계, 이미지 1/2 Motorola MBP667CONNECT Speaker Replacement: 4 단계, 이미지 2/2

    • Remove the black circular plastic part.

    편집

  6. Motorola MBP667CONNECT Speaker Replacement: 5 단계, 이미지 1/1

    • Remove the white plastic wire housing beneath the black plastic.

    편집

  7. Motorola MBP667CONNECT Speaker Replacement: 6 단계, 이미지 1/2 Motorola MBP667CONNECT Speaker Replacement: 6 단계, 이미지 2/2

    • Now, remove the bottom of the stand by pulling it from the camera.

    편집

  8. Motorola MBP667CONNECT Speaker Replacement, Speaker: 7 단계, 이미지 1/3 Motorola MBP667CONNECT Speaker Replacement, Speaker: 7 단계, 이미지 2/3 Motorola MBP667CONNECT Speaker Replacement, Speaker: 7 단계, 이미지 3/3

    • Remove the Phillips #1 screws on the back of the device.

    • Use a nylon spudger to remove the casing. This will separate the frontside of the camera from the backside.

    편집

  9. Motorola MBP667CONNECT Speaker Replacement: 8 단계, 이미지 1/2 Motorola MBP667CONNECT Speaker Replacement: 8 단계, 이미지 2/2

    • Now locate the brackets by the speaker on the frontside of the camera and use the metal spudger to carefully disconnect from casing.

    • Continue to use the metal spudger to carefully disconnect the remaining brackets from the casing.

    편집

  10. Motorola MBP667CONNECT Speaker Replacement: 9 단계, 이미지 1/2 Motorola MBP667CONNECT Speaker Replacement: 9 단계, 이미지 2/2

    • Using the soldering iron, desolder the speaker wires that are attached to the circuit board.

    • Use caution while handling the soldering iron. This tool gets very hot!

    • After desoldering the speaker wires, remove the wires from the circuit board.

    • Thread the wires from the new speaker wires through the holes in the circuit board. Using the soldering iron, re-solder the wires to the circuit board.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 4명과 함께

Kyle Kramer

회원 가입일: 01/16/19

255 평판

안내서 2개 작성하였습니다

배지: 2

팀

Eastern Washington University, Team S1-G6, Crawford Winter 2019 Eastern Washington University, Team S1-G6, Crawford Winter 2019 회원

EWU-CRAWFORD-W19S1G6

4 회원들

안내서 4개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 7

전체 시간: 184