기기를 수리하세요 커뮤니티 상점

Motorola Moto X Back Cover Assembly Replacement

단지 전제 조건
이 안내서는 다른 가이드의 선행 작업으로 사용하기 위한 것입니다. 그 자체로는 불완전합니다.

필요한 것

  1. Motorola Moto X Back Cover Assembly Replacement, Back Cover Assembly: 1 단계, 이미지 1/3 Motorola Moto X Back Cover Assembly Replacement, Back Cover Assembly: 1 단계, 이미지 2/3 Motorola Moto X Back Cover Assembly Replacement, Back Cover Assembly: 1 단계, 이미지 3/3

    • In the following steps you will be releasing the clips holding the phone's cases together. However, the back case is also secured with an adhesive pad. After separating the clips you will use an iOpener to allow the case to fully open. Do not attempt to fully open the phone before loosening the adhesive.

    • Insert a plastic opening tool into the seam between the front and rear covers near the SIM card slot.

    • Slide the plastic opening tool along the seam toward the upper corner.

    번역하기

  2. Motorola Moto X Back Cover Assembly Replacement: 2 단계, 이미지 1/2 Motorola Moto X Back Cover Assembly Replacement: 2 단계, 이미지 2/2

    • Carefully slide the plastic opening tool around the corner, freeing it from clips.

    번역하기

  3. Motorola Moto X Back Cover Assembly Replacement: 3 단계, 이미지 1/2 Motorola Moto X Back Cover Assembly Replacement: 3 단계, 이미지 2/2

    • Pry around the top right corner of the phone between the two covers.

    번역하기

  5. Motorola Moto X Back Cover Assembly Replacement: 4 단계, 이미지 1/3 Motorola Moto X Back Cover Assembly Replacement: 4 단계, 이미지 2/3 Motorola Moto X Back Cover Assembly Replacement: 4 단계, 이미지 3/3

    • Run the opening tool along the seam around all four sides, separating the remaining clips holding the cover on.

    • The plastic on the front cover is thinner near the buttons, and the buttons may move around. Go slowly to avoid damaging the buttons or the front cover.

    • Do not push the opening tool deep into phone, or you may damage internal components.

    번역하기

  6. Motorola Moto X Back Cover Assembly Replacement: 5 단계, 이미지 1/1

    • Heat an iOpener and lay it over the phone for approximately 90 seconds to loosen the adhesive securing the back cover.

    번역하기

  7. Motorola Moto X Back Cover Assembly Replacement: 6 단계, 이미지 1/3 Motorola Moto X Back Cover Assembly Replacement: 6 단계, 이미지 2/3 Motorola Moto X Back Cover Assembly Replacement: 6 단계, 이미지 3/3

    • Starting from the SIM slot side, carefully peel the back cover off of the phone.

    • The back cover is very flexible, but you don't want to damage any internal components by being too hasty.

    • There is a chance that the NFC coil may remain stubbornly adhered to the back cover. If that's the case, stop peeling the cover and reapply a heated iOpener to the back cover.

    • Do not separate the back cover entirely; it is still connected to the phone by the camera flash cable.

    • The flash cable is attached on the power/volume button side of the phone.

    번역하기

  8. Motorola Moto X Back Cover Assembly Replacement: 7 단계, 이미지 1/1

    • Gently set the back cover down in a way that exposes the camera flash cable connector, but does not put strain on it.

    번역하기

  9. Motorola Moto X Back Cover Assembly Replacement: 8 단계, 이미지 1/3 Motorola Moto X Back Cover Assembly Replacement: 8 단계, 이미지 2/3 Motorola Moto X Back Cover Assembly Replacement: 8 단계, 이미지 3/3

    • Use the tip of a spudger to flip up the retaining flap on the flash cable ZIF connector.

    • Be sure to pry only on the flap itself, not on the connector.

    • Pull the flash cable straight out of its socket.

    번역하기

  10. Motorola Moto X Back Cover Assembly Replacement: 9 단계, 이미지 1/1

    • Separate the back cover from the phone.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 7명과 함께

Sam Goldheart

회원 가입일: 10/18/12

465,970 평판

안내서 538개 작성하였습니다

배지: 48

배지 +45개 더

팀

iFixit iFixit 회원

Staff

136 회원들

안내서 17,299개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 3

30일 전: 11

전체 시간: 118