기기를 수리하세요 커뮤니티 상점

Motorola RIZR Z3 Slider Replacement

소개

Guide to replacing your phone's slider.

필요한 것

  1. Motorola RIZR Z3 Slider Replacement, Battery: 1 단계, 이미지 1/2 Motorola RIZR Z3 Slider Replacement, Battery: 1 단계, 이미지 2/2

    • Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.

    번역하기

  2. Motorola RIZR Z3 Slider Replacement: 2 단계, 이미지 1/2 Motorola RIZR Z3 Slider Replacement: 2 단계, 이미지 2/2

    • Tilt the battery by lifting at the exposed notch.

    • Slide the battery out of its casing.

    번역하기

  3. Motorola RIZR Z3 Slider Replacement, Motherboard: 3 단계, 이미지 1/1

    • Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.

    번역하기

  4. Motorola RIZR Z3 Slider Replacement: 4 단계, 이미지 1/2 Motorola RIZR Z3 Slider Replacement: 4 단계, 이미지 2/2

    • Use a plastic opening tool to lift the plastic casing.

    • Pull the plastic casing directly away from the phone.

    번역하기

  5. Motorola RIZR Z3 Slider Replacement: 5 단계, 이미지 1/1

    • Lift the black rubber loudspeaker housing up and out of the plastic casing.

    번역하기

  7. Motorola RIZR Z3 Slider Replacement: 6 단계, 이미지 1/2 Motorola RIZR Z3 Slider Replacement: 6 단계, 이미지 2/2

    • Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases.

    • Caution: Remove carefully, if broken, the phone will not be able to make calls.

    번역하기

  8. Motorola RIZR Z3 Slider Replacement: 7 단계, 이미지 1/2 Motorola RIZR Z3 Slider Replacement: 7 단계, 이미지 2/2

    • Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard.

    • Caution: Remove carefully, if broken, the phone will not function properly.

    번역하기

  9. Motorola RIZR Z3 Slider Replacement: 8 단계, 이미지 1/2 Motorola RIZR Z3 Slider Replacement: 8 단계, 이미지 2/2

    • Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out.

    • Caution: Do this gently Unclipping too fast may cause damage to your phone.

    번역하기

  10. Motorola RIZR Z3 Slider Replacement, LCD: 9 단계, 이미지 1/1

    • Turn the phone to the front.

    • Push the keypad out through the plastic casing.

    번역하기

  11. Motorola RIZR Z3 Slider Replacement: 10 단계, 이미지 1/1

    • Turn the phone to the side.

    • Thread the hinges of the slider through their holes in the casing and pull the slider down and away from the casing.

    번역하기

  12. Motorola RIZR Z3 Slider Replacement: 11 단계, 이미지 1/1

    • Use a T4 screwdriver to unscrew the two .15 inch screws holding the LCD to the faceplate.

    번역하기

  13. Motorola RIZR Z3 Slider Replacement: 12 단계, 이미지 1/3 Motorola RIZR Z3 Slider Replacement: 12 단계, 이미지 2/3 Motorola RIZR Z3 Slider Replacement: 12 단계, 이미지 3/3

    • Use a spudger to pry the plastic screen casing partially up from the LCD unit.

    • Use the spudger to pry the ribbon cable away from its clip on the LCD unit.

    • Caution: Do this carefully, damage to this ribbon cable will cause a blank screen.

    • Pull the plastic screen casing directly away from the LCD unit.

    번역하기

  14. Motorola RIZR Z3 Slider Replacement: 13 단계, 이미지 1/2 Motorola RIZR Z3 Slider Replacement: 13 단계, 이미지 2/2

    • Use a spudger to lift the LCD partially away from the metal casing.

    • Use the spudger to pry the ribbon cable directly up from its clip on the metal casing.

    • Caution: Damage to the ribbon cable here will cause screen damage.

    • Pull the LCD completely away from the metal casing.

    번역하기

  15. Motorola RIZR Z3 Slider Replacement, Slider: 14 단계, 이미지 1/2 Motorola RIZR Z3 Slider Replacement, Slider: 14 단계, 이미지 2/2

    • Use the pointed end of a spudger to push the black peg into the larger side of the slot.

    • Push the peg through so that it is completely clear of the slot.

    번역하기

  16. Motorola RIZR Z3 Slider Replacement: 15 단계, 이미지 1/1

    • Turn the phone around and slide the slider down its track until it is free of the casing.

    • The ribbon that fits into the rectangular slot on the slider will slip through this slot as you detach the slider.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

Andrew Vu

회원 가입일: 10/07/11

35 평판

안내서 2개 작성하였습니다

배지: 6

배지 +3개 더

팀

Cal Poly, Team 5-34, Amido Fall 2011 Cal Poly, Team 5-34, Amido Fall 2011 회원

CPSU-AMIDO-F11S5G34

4 회원들

안내서 6개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 1

전체 시간: 1,268