기기를 수리하세요 커뮤니티 상점

Neato BOTVAC CONNECTED Front Roller Brush Replacement

소개

In this guide you will be able to replace the front roller of the Neato Botvac Connected. This will need to be replaced if there is excessive noise coming from the vacuum or if there are excess debris. In order to complete this guide you must first follow the guide to disconnect the battery.

필요한 것

  1. Neato BOTVAC CONNECTED Front Roller Brush Replacement, Battery: 1 단계, 이미지 1/1

    • Place the top of the Neato Botvac Connected against a flat surface.

    편집

  2. Neato BOTVAC CONNECTED Front Roller Brush Replacement: 2 단계, 이미지 1/2 Neato BOTVAC CONNECTED Front Roller Brush Replacement: 2 단계, 이미지 2/2

    • Remove the two 5.5 mm screws with a Phillips #2 screwdriver.

    편집

  3. Neato BOTVAC CONNECTED Front Roller Brush Replacement: 3 단계, 이미지 1/2 Neato BOTVAC CONNECTED Front Roller Brush Replacement: 3 단계, 이미지 2/2

    • Using the spudger, remove the panel covering the battery.

    편집

  4. Neato BOTVAC CONNECTED Front Roller Brush Replacement: 4 단계, 이미지 1/3 Neato BOTVAC CONNECTED Front Roller Brush Replacement: 4 단계, 이미지 2/3 Neato BOTVAC CONNECTED Front Roller Brush Replacement: 4 단계, 이미지 3/3

    • Gently remove the connecting wires attached to the battery.

    • The wires are attached to the vacuum through a clip.

    편집

  6. Neato BOTVAC CONNECTED Front Roller Brush Replacement: 5 단계, 이미지 1/1

    • Using the spudger, gently remove the battery from the device.

    편집

  7. Neato BOTVAC CONNECTED Front Roller Brush Replacement, Front Roller Brush: 6 단계, 이미지 1/2 Neato BOTVAC CONNECTED Front Roller Brush Replacement, Front Roller Brush: 6 단계, 이미지 2/2

    • Remove the following screws with a Torx screwdriver:

    • Four 2.3 mm screws.

    편집

  8. Neato BOTVAC CONNECTED Front Roller Brush Replacement: 7 단계, 이미지 1/1

    • Gently remove the thin panel held by the four screws with a spudger.

    편집

  9. Neato BOTVAC CONNECTED Front Roller Brush Replacement: 8 단계, 이미지 1/1

    • Gently remove the two small wheels, and the axles attached to them.

    편집

  10. Neato BOTVAC CONNECTED Front Roller Brush Replacement: 9 단계, 이미지 1/1

    • Gently remove the panel that is on top of the front roller with the spudger.

    편집

  11. Neato BOTVAC CONNECTED Front Roller Brush Replacement: 10 단계, 이미지 1/1

    • Gently remove the front brush.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 3명과 함께

Justin Silva

회원 가입일: 03/20/23

645 평판

안내서 5개 작성하였습니다

배지: 5

배지 +2개 더

팀

UMass Dartmouth, Team 6-3, Botvin Spring 2023 UMass Dartmouth, Team 6-3, Botvin Spring 2023 회원

UMASSD-BOTVIN-S23S6G3

4 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 7

전체 시간: 120