기기를 수리하세요 커뮤니티 상점

Neato Botvac 65 Wheel Motors Replacement

소개

Step by Step instructions to replace Neato Botvac 65 wheel motors.

필요한 것

  1. Neato Botvac 65 Wheel Motors Replacement, Battery: 1 단계, 이미지 1/2 Neato Botvac 65 Wheel Motors Replacement, Battery: 1 단계, 이미지 2/2

    • Flip the device upside down.

    • Locate the two (2) 20mm screws on the batttery plate.

    편집

  2. Neato Botvac 65 Wheel Motors Replacement: 2 단계, 이미지 1/2 Neato Botvac 65 Wheel Motors Replacement: 2 단계, 이미지 2/2

    • Use the Phillips #1 screwdriver to loosen both screws.

    편집

  3. Neato Botvac 65 Wheel Motors Replacement: 3 단계, 이미지 1/1

    • Remove the battery back plate to reveal the battery.

    편집

  4. Neato Botvac 65 Wheel Motors Replacement: 4 단계, 이미지 1/2 Neato Botvac 65 Wheel Motors Replacement: 4 단계, 이미지 2/2

    • Disconnect the current battery by pulling the connector from the base and pushing on the clip.

    편집

  5. Neato Botvac 65 Wheel Motors Replacement, Brush: 5 단계, 이미지 1/1

    • Flip the device upside down.

    편집

  6. Neato Botvac 65 Wheel Motors Replacement: 6 단계, 이미지 1/2 Neato Botvac 65 Wheel Motors Replacement: 6 단계, 이미지 2/2

    • Use the screwdriver to take off the four (4) 10mm screws located near the brush which secure the plastic guard.

    편집

  8. Neato Botvac 65 Wheel Motors Replacement: 7 단계, 이미지 1/2 Neato Botvac 65 Wheel Motors Replacement: 7 단계, 이미지 2/2

    • Remove the plastic brush guard.

    • Pull off the plastic covering the brush.

    편집

  9. Neato Botvac 65 Wheel Motors Replacement: 8 단계, 이미지 1/1

    • Lift the brush to clean or replace.

    편집

  10. Neato Botvac 65 Wheel Motors Replacement, Top Cover: 9 단계, 이미지 1/1

    • Flip device upside down.

    • Locate the six (6) screw connected to the top cover.

    편집

  11. Neato Botvac 65 Wheel Motors Replacement: 10 단계, 이미지 1/1

    • Remove eight (8) star screws using the T10 bit.

    편집

  12. Neato Botvac 65 Wheel Motors Replacement: 11 단계, 이미지 1/2 Neato Botvac 65 Wheel Motors Replacement: 11 단계, 이미지 2/2

    • Pull off one side of the brush front cover, and then pull off the other.

    편집

  13. Neato Botvac 65 Wheel Motors Replacement: 12 단계, 이미지 1/1

    • Flip right side up and turn around.

    • FInd the two clips connecting the top cover to the body of the device.

    편집

  14. Neato Botvac 65 Wheel Motors Replacement: 13 단계, 이미지 1/2 Neato Botvac 65 Wheel Motors Replacement: 13 단계, 이미지 2/2

    • Lift up on the top cover gently.

    • Disconnect the connector from the motherboard to detach the top cover from the robot.

    편집

  15. Neato Botvac 65 Wheel Motors Replacement, Wheel Motors: 14 단계, 이미지 1/3 Neato Botvac 65 Wheel Motors Replacement, Wheel Motors: 14 단계, 이미지 2/3 Neato Botvac 65 Wheel Motors Replacement, Wheel Motors: 14 단계, 이미지 3/3

    • Remove four (4) 10mm 'star' screws using the T10 bit from the base plate where the rotating infrared sensor is located.

    • Carefully place the sensor on or near the robot without pulling the wires out.

    편집

  16. Neato Botvac 65 Wheel Motors Replacement: 15 단계, 이미지 1/1

    • Remove two (2) screws using the T10 bit that connects the plastic protector over the wheel motor.

    • Pull up on the metal weight to remove.

    편집

  17. Neato Botvac 65 Wheel Motors Replacement: 16 단계, 이미지 1/2 Neato Botvac 65 Wheel Motors Replacement: 16 단계, 이미지 2/2

    • Flip the botvac over being careful not to drop the IR sensor or cause damage to the wires.

    • Using a flat-head screw driver and a cloth for protection, press on the clips until they recede into the botvac.

    편집

  18. Neato Botvac 65 Wheel Motors Replacement: 17 단계, 이미지 1/2 Neato Botvac 65 Wheel Motors Replacement: 17 단계, 이미지 2/2

    • Flip the robot back over(right-side up).

    • Carefully remove the plastic cover that protects the motor.

    편집

  19. Neato Botvac 65 Wheel Motors Replacement: 18 단계, 이미지 1/3 Neato Botvac 65 Wheel Motors Replacement: 18 단계, 이미지 2/3 Neato Botvac 65 Wheel Motors Replacement: 18 단계, 이미지 3/3

    • Carefully remove the motor that you wish to replace.

    • Trace the wires that are connected to the motor back to the motherboard.

    • Disconnect the connector from the motherboard for the respective motor you're replacing.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Joseph Caton

회원 가입일: 02/15/17

334 평판

안내서 3개 작성하였습니다

배지: 10

배지 +7개 더

팀

USF Tampa, Team S2-G1, Lacy Spring 2017 USF Tampa, Team S2-G1, Lacy Spring 2017 회원

USFT-LACY-S17S2G1

4 회원들

안내서 10개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 4

30일 전: 6

전체 시간: 1,456