기기를 수리하세요 커뮤니티 상점

Nerf N-Strike Elite Strongarm Barrel Replacement

소개

This guide will show how to remove the barrel from the blaster. A good test to check if the barrel is stuck is shown in Step 6 (we suggest to do this before opening the blaster).

필요한 것

  1. Nerf N-Strike Elite Strongarm Barrel Replacement, Outer Shell: 1 단계, 이미지 1/2 Nerf N-Strike Elite Strongarm Barrel Replacement, Outer Shell: 1 단계, 이미지 2/2

    • Lay the Nerf Strongarm on its side, left side facing up.

    번역하기

  2. Nerf N-Strike Elite Strongarm Barrel Replacement: 2 단계, 이미지 1/2 Nerf N-Strike Elite Strongarm Barrel Replacement: 2 단계, 이미지 2/2

    • Locate the 12 Philips head screws and remove them: Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm

    번역하기

  3. Nerf N-Strike Elite Strongarm Barrel Replacement: 3 단계, 이미지 1/1

    • Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.

    • The other half of the cocking mechanism is connected with a spring which may slide off the blaster. Be advised this is normal but worth watching to avoid damaging the spring.

    번역하기

  4. Nerf N-Strike Elite Strongarm Barrel Replacement: 4 단계, 이미지 1/1

    • At this time, remove the blaster cover to reveal its internals.

    • If the blaster is resting on its side, the barrel may shift slightly as it is leaning on itself (seen in the image). This is normal but should be handled with care to keep the blaster together.

    번역하기

  6. Nerf N-Strike Elite Strongarm Barrel Replacement: 5 단계, 이미지 1/1

    • Once the screws have been removed, lift the top half of the gun off.

    • Notice, the gray colored piece must be removed first in order for the larger half to be removed.

    • Take care and try not to lose any smaller pieces as you open it up.

    • Locking tab for attachments.

    번역하기

  7. Nerf N-Strike Elite Strongarm Barrel Replacement, Barrel: 6 단계, 이미지 1/1

    • Start by inspecting the barrel closer for broken components.

    • Pressing the unloading button is a good test to check if the barrel will rotate out.

    • If the barrel fails to cooperate, continue onto the next steps.

    번역하기

  8. Nerf N-Strike Elite Strongarm Barrel Replacement: 7 단계, 이미지 1/1

    • Once the cover is off, the barrel component will be free and removable.

    번역하기

  9. Nerf N-Strike Elite Strongarm Barrel Replacement: 8 단계, 이미지 1/1

    • Once the barrel is removed, continue by removing the front shaft. This component is also independent of the blaster and does not require tools.

    번역하기

  10. Nerf N-Strike Elite Strongarm Barrel Replacement: 9 단계, 이미지 1/1

    • Look for any signs of debris or any damaged locations that may be causing the barrel to lock.

    번역하기

  11. Nerf N-Strike Elite Strongarm Barrel Replacement: 10 단계, 이미지 1/1

    • At this time, all components interacting with the barrel are removed.

    • Take this time to inspect the barrel for any signs of debris or damaged locations.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 9명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 3명과 함께

Alexander Kim

회원 가입일: 08/27/15

832 평판

안내서 3개 작성하였습니다

배지: 14

배지 +11개 더

팀

USF Tampa, Team 5-4, Blackwell Fall 2015 USF Tampa, Team 5-4, Blackwell Fall 2015 회원

USFT-BLACKWELL-F15S5G4

4 회원들

안내서 12개 작성하였습니다

댓글 한 개

hi my barrel keeps ritating and is not fixed and does not stay aligned to the shooting point what shall i do

cryo17 - 답글

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 8

30일 전: 25

전체 시간: 12,176