이 버전에는 잘못된 편집 사항이 있을 수 있습니다. 최신 확인된 스냅샷으로 전환하십시오.
필요한 것
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the display's metal outer ring with your fingers and pull directly away from the wall.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Turn the display over.
-
Remove the four 6 mm screws from the back of the display using a Phillips #0 screwdriver.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pinch the gray 20-pin connector with your fingers and pull directly away from the display.
I pinched the connector and it will not pull out
I’m my case, the white backplate cannot be pulled until it is turned about 1cm counterclockwise to disengage the brackets that hold to the internal plate. To do this, yo need to hold the front of the Nest with the metal frame (so the it doesn’t turn), while turning the backplate.
And in my case, there are only 2 screws (in the 9 and 3 o’clock positions) and not 4 as shown in the photo.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Locate the blue pull tab at the end of the ribbon which says, "1. Pull".
-
Grasp the tab with your fingers and pull directly away from the motherboard.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Locate the blue tab which says, "2. Pull".
-
Use tweezers to pull the battery up and away from the display.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Locate the blue tab which says "3 unplug".
-
Grasp the battery with your fingers. Pull gently directly away from the display to unplug the battery from the motherboard.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Grasp the battery with your fingers and pull directly away from motherboard to separate the battery from the display.
Same question
At least say the tipe of battery that's needed.
I just ordered the battery model specified. When it arrived, I realized it doesn’t have the same specs as the battery that comes with the thermostat.
The part listed (TL284443) is 3.7 VDC, but it is only is 380mAh (1.41 Wh) (if you zoom in on the image when you click “Buy”, you can see)
You can clearly see in the tear-down that the battery that comes with the thermostat is 2.1 Wh.
It might work as a replacement, but doesn’t have the same capacity.
To be fair, most people don’t know that there are different generations of the Nest Thermostat and clearly they didn’t read that this was for the 2nd generation Nest Thermostat. Probably should have been pointed out in the instructions more clearly for those folks. Then they wouldn’t have been so confused about the battery voltage differences.
I am a 64 year old woman, I had the Nest next generation installed last year. So far it keeps telling me that the connection to my wi-Fi is not working and now it’s saying the battery is dead. I’ve gone through all the steps to re-connect to wi-fi to no avail. Could this be because the battery needs replacing?
It’s 68 degrees in my house now and that’s thanks to my fireplace not this horrible device. I am going back to the regular thermostat, what a waste of hard earned money.
-
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the four 3mm screws with a #0 Phillips screwdriver.
-
Remove the one 4mm screw located at the edge of the auto-away sensor. Use a #0 Phillips screwdriver.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Lift the auto-away sensor from motherboard using tweezers.
-
Peel the copper foil gently from the EMI shield.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove one 4 mm screw from the motherboard using a #0 Phillips screwdriver.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Remove the EMI shield from the motherboard using the plastic opening tools.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Locate the black tabs that hold the display to the motherboard.
-
Push the black tabs gently away from the motherboard using the plastic opening tools.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Push the crescent shape bottom of the display away from the plastic frame using the plastic opening tools.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pry the front glass and plastic frame apart gently using the plastic opening tools.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pry the LCD screen gently from the plastic frame using the plastic opening tools.
-
-
이 단계는 번역되지 않았습니다. 번역을 도와주십시오
-
Pull the LCD screen away from the plastic frame gently using your fingers.
-
다른 8명이 해당 안내서를 완성하였습니다.
댓글 5개
Thank you for providing this tutorial. My dog, not making this up, knocked my nest off the wall. Where can I purchase the replacement green itself and the plastic opening tools you used throughout the repair? This will be my first time on something like this, but with your guide I should have a decent shot at not screwing it up.
Skip step 12. There is no reason to remove the EMI shield.
Where can you get the replacement lcd screen for gen 2 nest learning thermostat?
Stan Griff - 답글