주요 콘텐츠로 건너뛰기

소개

Use this guide to replace the motherboard in your Nexus 5.

  1. Insert a SIM card eject tool or a  paper clip into the hole next to the SIM card slot, which is located just under the power button. Push  the tool into the hole until you see the card pop out.
    • Insert a SIM card eject tool or a paper clip into the hole next to the SIM card slot, which is located just under the power button.

    • Push the tool into the hole until you see the card pop out.

  2. Gently remove the SIM card with your fingers, or a pair of tweezers if the SIM holder does not fully eject.
    • Gently remove the SIM card with your fingers, or a pair of tweezers if the SIM holder does not fully eject.

    • Make sure the chip is facing the rear of the phone when reinserting the SIM card.

  3. Use a plastic opening tool to free the clips on the top and each side of the back cover. The bottom is secured with some adhesive foam. You should be able to finally free the back cover using an opening pick. It's best to avoid prying around the SIM card slot, as the plastic here is very thin and likely to break from prying.
    • Use a plastic opening tool to free the clips on the top and each side of the back cover.

    • The bottom is secured with some adhesive foam. You should be able to finally free the back cover using an opening pick.

    • It's best to avoid prying around the SIM card slot, as the plastic here is very thin and likely to break from prying.

  4. Remove the six 4.0 mm Phillips #00  screws that secure the midframe to the phone.
    • Remove the six 4.0 mm Phillips #00 screws that secure the midframe to the phone.

    • To replace the LCD screen and digitizer, remove the additional four 4.0mm daughterboard cover screws with the same screwdriver.

  5. Remove the midframe from the phone. Remove the midframe from the phone.
    • Remove the midframe from the phone.

    • Use the flat end of a nylon spudger to disconnect the battery connector.

  6. Use the flat end of a spudger to disconnect the daughterboard ribbon cable and pull it away from the battery. Use the flat end of a spudger to disconnect the daughterboard ribbon cable and pull it away from the battery.
    • Use the flat end of a spudger to disconnect the daughterboard ribbon cable and pull it away from the battery.

  7. Use a plastic opening tool to pry the battery out of its housing. You may need to use a heat gun to apply a small amount of heat to soften the adhesive below the battery. Do not puncture or bend the battery.
    • Use a plastic opening tool to pry the battery out of its housing.

    • You may need to use a heat gun to apply a small amount of heat to soften the adhesive below the battery.

    • Do not puncture or bend the battery.

  8. Use the flat end of a spudger to disconnect the left antenna cable. Use the flat end of a spudger to disconnect the left antenna cable.
    • Use the flat end of a spudger to disconnect the left antenna cable.

  9. Use the flat end of a spudger to disconnect the right antenna cable. These must be firmly secured during reassembly. Failure to secure the antenna connections will affect your reception and call quality.
    • Use the flat end of a spudger to disconnect the right antenna cable.

    • These must be firmly secured during reassembly. Failure to secure the antenna connections will affect your reception and call quality.

  10. Use the flat end of a spudger to disconnect the ribbon cable that connects rear-facing camera to the motherboard. Use the flat end of a spudger to disconnect the ribbon cable that connects rear-facing camera to the motherboard.
    • Use the flat end of a spudger to disconnect the ribbon cable that connects rear-facing camera to the motherboard.

  11. Use the flat end of a spudger to disconnect the front camera ribbon cable. Use the flat end of a spudger to disconnect the front camera ribbon cable.
    • Use the flat end of a spudger to disconnect the front camera ribbon cable.

  12. Gently lift the motherboard up and out of the device. Gently lift the motherboard up and out of the device.
    • Gently lift the motherboard up and out of the device.

결론

To reassemble your device, follow these instructions in reverse order.

다른 28명이 해당 안내서를 완성하였습니다.

Kyle Libby

회원 가입일: 2014년 04월 07일

964 평판

안내서 7개 작성하였습니다

Cal Poly, Team 7-23, Regan Spring 2014 Cal Poly, Team 7-23, Regan Spring 2014 회원

CPSU-REGAN-S14S7G23

4 회원들

안내서 18개 작성하였습니다

is the motherboard from the 32gb nexus 5, compatible for the nexus 5 16gb lcd??

Vandalismo Teevee - 답글

It should be, yes. I've chopped and changed loads of Nexus 5 phone around and haven't had a problem.

drunkenmenace -

Thanks for the repy. My Nexus 5 has some bootoop problems and when i go to the boot options, (the hold power and volume down), it says Lock State - LOCKED. so im thinking of replacing the motherboard. or is there a way to fix my problem? Thanks for the reply. I appreciate it.

Vandalismo Teevee - 답글

My Nexus 5 just switched off while i was recording a video. It isnt switching on now. How to bring it back to life??Any solution will b of great help. Thanks

Jasmine K - 답글

I just used this guide to quickly get at the motherboard to replace a faulty power button. It's tedious but not impossible with a very clean soldering iron tip, solder wick, and lots of flux. The replacement button and covers from iFixit were an exact match (I checked under a microscope).

Mark Renouf - 답글

댓글 쓰기

조회 통계:

지난 24시간: 6

지난 7일: 31

지난 30일: 172

전체 시간: 31,676