메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Nikon COOLPIX S610c Front Casing Replacement

작성자 Bryan Bell (또 다른 기여자 3명)
  • 댓글 0
  • 즐겨찾기 0

난이도

보통

단계

17

소요 시간

45 분

섹션

3

플래그

2

Action Shots

액션 샷

액션 영웅이 되십시오! 해당 안내서는 특정 액션을 더 잘 보여주기 위한 사진들이 필요합니다.

Step Trimmer

단계 다듬기

해당 안내서에는 불필요한 단계들이 있습니다. 단계들을 다듬어 더욱 간결하게 만들어 주십시오!

소개

If your front casing has come loose or needs to be replaced, follow this guid to remove your current front casing from the camera.

도구

해당 도구 구매

부품

부품은 필요하지 않습니다.

  1. On the bottom right of the camera, locate the battery flap switch.

    • On the bottom right of the camera, locate the battery flap switch.

    편집

  2. Move this switch to the right so the battery flap can flip open.

    • Move this switch to the right so the battery flap can flip open.

    편집

  3. Slide the orange switch to the right as shown. Now the battery can be pulled out. Reverse these steps to re-install.

    • Slide the orange switch to the right as shown. Now the battery can be pulled out. Reverse these steps to re-install.

    편집

  4. Remove the three 3x3mm screws attached to the rear casing.

    • Remove the three 3x3mm screws attached to the rear casing.

    편집

  5. The panel can be identified by the wifi logo on its upper half on the camera's side.

    • The panel can be identified by the wifi logo on its upper half on the camera's side.

    • Remove the 5x3mm screw holding down the panel on the side closest to the lens.

    편집

  6. Pry the panel off from the bottom using your fingernail.

    • Pry the panel off from the bottom using your fingernail.

    편집

  7. US$100.00 이상 또는 Pro Tech Toolkit을 포함한 모든 주문의 배송은 무료입니다!

    상점 둘러보기

    Ever fixed something? That’s Genius.

    Share your repair story with #ImAGenius

    We Are All Geniuses

    Share your repair story with #ImAGenius

  8. Remove the 3x2mm screw underneath the panel near the top of the camera.

    • Remove the 3x2mm screw underneath the panel near the top of the camera.

    편집

  9. Remove the 4x3mm on the opposite side near the selector wheel. Remove the 2x2mm and 3x2mm screws underneath the a/v flap.

    • Remove the 4x3mm on the opposite side near the selector wheel.

    • Remove the 2x2mm and 3x2mm screws underneath the a/v flap.

    편집

  10. Pry the back panel away from the body of the camera, using the space you just opened up. Be careful not to damage the ribbon cable on the opposite end of the camera.

    • Pry the back panel away from the body of the camera, using the space you just opened up.

    • Be careful not to damage the ribbon cable on the opposite end of the camera.

    • A small piece of the frame of the camera may fall off, but it can be easily put back into place during reassembly.

    편집

  11. Pry up the plastic ribbon connectors on the body of the camera to release the ribbon cables. The center connector is detached by flipping the black latch up and away from the center of the camera.

    • Pry up the plastic ribbon connectors on the body of the camera to release the ribbon cables.

    • The center connector is detached by flipping the black latch up and away from the center of the camera.

    • The smaller connector is detached by flipping the tan latch up and away from the edge of the camera.

    편집

  12. Remove the three 3x3mm screws that attach the front casing to the bottom.

    • Remove the three 3x3mm screws that attach the front casing to the bottom.

    편집

  13. Remove the two 3x2 screws and two 3.5x2.5 screws attaching the rear panel to the motherboard.

    • Remove the two 3x2 screws and two 3.5x2.5 screws attaching the rear panel to the motherboard.

    편집

  14. Lift the back panel off the motherboard. Be careful not to damage the ribbon cable that attaches the mother board to the rear panel.

    • Lift the back panel off the motherboard.

    • Be careful not to damage the ribbon cable that attaches the mother board to the rear panel.

    편집

  15. Detach the ribbon cable from the motherboard by flipping up the latch on the ribbon connector. Note that the white ribbon connector latch flips away from the ribbon cable.

    • Detach the ribbon cable from the motherboard by flipping up the latch on the ribbon connector.

    • Note that the white ribbon connector latch flips away from the ribbon cable.

    편집

  16. Remove the final 4x3mm screw at the top of the camera near the lens. Remove the final 4x3mm screw at the top of the camera near the lens.

    • Remove the final 4x3mm screw at the top of the camera near the lens.

    편집

  17. Pry the front casing away from the body of the camera. Be careful not to damage the wires that attach the front panel to the motherboard.

    • Pry the front casing away from the body of the camera.

    • Be careful not to damage the wires that attach the front panel to the motherboard.

    • Short the leads on the capacitor near the flash to avoid a nasty shock when separating the casing from the body.

    편집

  18. Unscrew the three 3x2mm screws that attach the cables to the front casing.

    • Unscrew the three 3x2mm screws that attach the cables to the front casing.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 3명과 함께

Bryan Bell

회원 가입일: 2012년 01월 26일

28 평판

안내서 1개 작성함

배지: 5

배지 +2개 더

팀

Cal Poly, Team 9-5, Regan Winter 2012 Cal Poly, Team 9-5, Regan Winter 2012 회원

CPSU-REGAN-W12S9G5

5 회원들

안내서 6개 작성하였습니다

댓글 0개

의견 추가하세요
조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 0

전체 시간: 1,036