기기를 수리하세요

수리할 권리

상점

Nintendo 64 Bottom Cover Disassembly

작성자 tonymag28 (또 다른 기여자 4명)
  • 댓글 2
  • 즐겨찾기 17
  • 완료: 17

난이도

보통

단계

17

소요 시간

15 - 20 분

섹션

4

플래그

0

소개

This is how you remove the bottom cover

  1. Remove the expansion pack cover by pushing in the tab and pulling out.

    • Remove the expansion pack cover by pushing in the tab and pulling out.

    편집

  2. If your system uses a jumper pack, the same procedure applies to remove it.

    • If your system uses a jumper pack, the same procedure applies to remove it.

    • A small spoon can be used in place of a spudger.

    • Lever the expansion pack out using a metal spudger.

    편집

  3. Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    • Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    편집

  4. Remove the two front feet of the N64.

    • Remove the two front feet of the N64.

    편집

  5. Rotate to top side up and lift off top cover.

    • Rotate to top side up and lift off top cover.

    편집

  6. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    • Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    편집

  8. Remove the metal plate indicated in the example by sliding it back and then lifting it up. Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    • Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    편집

  9. Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    • Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    편집

  10. Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    • Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    편집

  11. Remove the small metal bracket from the back of the expansion pack slot.

    • Remove the small metal bracket from the back of the expansion pack slot.

    편집

  12. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    • Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    편집

  13. Remove the small metal bracket behind the expansion slot using the spudger. Remove the small metal bracket behind the expansion slot using the spudger.

    • Remove the small metal bracket behind the expansion slot using the spudger.

    편집

  14. Remove the seven screws indicated in the example using the larger Phillips screwdriver. Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    • Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    편집

  15. Lift off and remove the metal plate as indicated in the example.

    • Lift off and remove the metal plate as indicated in the example.

    편집

  16. Remove the four screws indicated using the #1 Phillips screwdriver.

    • Remove the four screws indicated using the #1 Phillips screwdriver.

    편집

  17. Lift up and remove the motherboard.

    • Lift up and remove the motherboard.

    편집

  18. Remove everything from the bottom cover.

    • Remove everything from the bottom cover.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 17명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

tonymag28

회원 가입일: 2009년 10월 28일

1,934 평판

안내서 3개 작성하였습니다

배지: 13

배지 +10개 더

팀

Cal Poly, Team 5-4, Regan Fall 2009 Cal Poly, Team 5-4, Regan Fall 2009 회원

CPSU-REGAN-F09S5G4

7 회원들

안내서 6개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

24 시간 전: 15

7일 전: 81

30일 전: 399

전체 시간: 29,131