메뉴

설정

내 작업대

귀하의 기기에 대한 안내서, 부품 및 답변에 신속히 접근할 수 있습니다
내 장바구니

장바구니가 비어 있는 것 같습니다

상점 둘러보기

Nintendo 64 Metal Plate Replacement

작성자 LisaF818 (또 다른 기여자 8명)
  • 댓글 2
  • 즐겨찾기 11
  • 완료: 3

난이도

쉬움

단계

14

소요 시간

15 분

섹션

2

플래그

0

소개

This guide shows how to remove the metal plate that covers the motherboard.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Remove the expansion pack cover by pushing in the tab and pulling out.

    • Remove the expansion pack cover by pushing in the tab and pulling out.

    편집

  2. If your system uses a jumper pack, the same procedure applies to remove it.

    • If your system uses a jumper pack, the same procedure applies to remove it.

    • A small spoon can be used in place of a spudger.

    • Lever the expansion pack out using a metal spudger.

    편집

  3. Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    • Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    편집

  4. Remove the two front feet of the N64.

    • Remove the two front feet of the N64.

    편집

  5. Rotate to top side up and lift off top cover.

    • Rotate to top side up and lift off top cover.

    편집

  6. 맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

    맥북 배터리 수리 키트

    기본 가격은 $69.99

    Buy Now

  7. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    • Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    편집

  8. Remove the metal plate indicated in the example by sliding it back and then lifting it up. Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    • Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    편집

  9. Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    • Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    편집

  10. Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    • Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    편집

  11. Remove the small metal bracket from the back of the expansion pack slot.

    • Remove the small metal bracket from the back of the expansion pack slot.

    편집

  12. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    • Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    편집

  13. Remove the small metal bracket behind the expansion slot using the spudger. Remove the small metal bracket behind the expansion slot using the spudger.

    • Remove the small metal bracket behind the expansion slot using the spudger.

    편집

  14. Remove the seven screws indicated in the example using the larger Phillips screwdriver. Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    • Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    편집

  15. Lift off and remove the metal plate as indicated in the example.

    • Lift off and remove the metal plate as indicated in the example.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 3명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 8명과 함께

LisaF818

회원 가입일: 2009년 11월 29일

104 평판

안내서 1개 작성함

배지: 8

배지 +5개 더

팀

Cal Poly, Team 5-4, Regan Fall 2009 Cal Poly, Team 5-4, Regan Fall 2009 회원

CPSU-REGAN-F09S5G4

7 회원들

안내서 6개 작성하였습니다

댓글 0개

의견 추가하세요

댓글 쓰기

조회 통계:

지난 24시간: 2

지난 7일: 5

지난 30일: 27

전체 시간: 9,153