주요 콘텐츠로 건너뛰기

Nintendo Switch Micro SD Card Reader Replacement

필요한 것

  1. Nintendo Switch Micro SD Card Reader Replacement, Release the Joy Con controller locking tabs: 1 단계, 이미지 1/3 Nintendo Switch Micro SD Card Reader Replacement, Release the Joy Con controller locking tabs: 1 단계, 이미지 2/3 Nintendo Switch Micro SD Card Reader Replacement, Release the Joy Con controller locking tabs: 1 단계, 이미지 3/3
    • Before you begin this repair, make sure the device is completely powered off.

    • Press and hold down the small round button on the back of the Joy Con controller.

    • While you hold down the button, slide the controller upward.

  2. Nintendo Switch Micro SD Card Reader Replacement, Remove the Joy Con controllers: 2 단계, 이미지 1/3 Nintendo Switch Micro SD Card Reader Replacement, Remove the Joy Con controllers: 2 단계, 이미지 2/3 Nintendo Switch Micro SD Card Reader Replacement, Remove the Joy Con controllers: 2 단계, 이미지 3/3
    • Continue sliding the Joy Con upward until it's completely removed from the console.

    • Repeat this same process for the other Joy Con.

  3. Nintendo Switch Micro SD Card Reader Replacement, Remove the back-side screws: 3 단계, 이미지 1/1
    이 단계에 사용된 도구:
    Magnetic Project Mat
    $19.95
    구매
    • Use a Y00 screwdriver to remove the four 6.3 mm-long screws securing the rear panel.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

  4. Nintendo Switch Micro SD Card Reader Replacement, Remove the top and bottom screws: 4 단계, 이미지 1/2 Nintendo Switch Micro SD Card Reader Replacement, Remove the top and bottom screws: 4 단계, 이미지 2/2
    • Use a JIS 000 driver or an official iFixit PH 000 driver to remove the following screws securing the rear panel:

    • One 2.5 mm-long screw on the top edge of the device

    • Two 2.5 mm-long screws on the bottom edge of the device

    • To prevent these tight screws from stripping, apply firm downward force, work slowly and try another JIS 000 or PH 000 driver if the screws won't come out.

  5. Nintendo Switch Micro SD Card Reader Replacement: 5 단계, 이미지 1/2 Nintendo Switch Micro SD Card Reader Replacement: 5 단계, 이미지 2/2
    • Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the two 3.8 mm center screws on the sides of the device (one on each side).

  6. Nintendo Switch Micro SD Card Reader Replacement: 6 단계, 이미지 1/2 Nintendo Switch Micro SD Card Reader Replacement: 6 단계, 이미지 2/2
    • Use your finger to flip up the kickstand on the back of the device.

    • If there's a microSD card in the microSD card slot, remove it now before you continue to the next step.

  7. Nintendo Switch Micro SD Card Reader Replacement: 7 단계, 이미지 1/1
    • Use a JIS 000 screwdriver or an official iFixit PH 000 driver to remove the 1.6 mm screw in the kickstand well.

    • Close the kickstand.

  8. Nintendo Switch Micro SD Card Reader Replacement: 8 단계, 이미지 1/3 Nintendo Switch Micro SD Card Reader Replacement: 8 단계, 이미지 2/3 Nintendo Switch Micro SD Card Reader Replacement: 8 단계, 이미지 3/3
    • Open the game card cartridge flap.

    • The game card cartridge flap attaches to the other half of the plastic shell, preventing you from completely lifting up the rear panel if it's closed.

    • Lift the rear panel up from the bottom of the device and remove it.

  9. Nintendo Switch Micro SD Card Reader Replacement, Micro SD Card Reader: 9 단계, 이미지 1/1
    • Remove the single 3.1 mm Phillips screw from micro SD card board.

  10. Nintendo Switch Micro SD Card Reader Replacement: 10 단계, 이미지 1/2 Nintendo Switch Micro SD Card Reader Replacement: 10 단계, 이미지 2/2
    • Gently lift the micro SD card board straight up, away from the Switch to disconnect and remove it.

    • During reassembly, line up the micro SD card board and lightly press on the foam pad until the press connector snaps into place to reconnect it.

결론

To reassemble your device, follow these instructions in reverse order.

다른 138명이 해당 안내서를 완성하였습니다.

Blake Klein

회원 가입일: 01/29/17

70,356 평판

안내서 50개 작성하였습니다

댓글 49개

My SD reader never worked.

Used this guide to find that it was never seated correctly. Reseated and now works perfectly. THANK YOU!

Finx O'Mally - 답글

My console won’t boot if I have an SD card inserted after reseating it. What should I do?

Ewan MacInnis - 답글

Easy guide, fixed my problem. Changed the SD card reader cause I was abusing of it by putting SD in and out constantly.

Nicola Bonardi - 답글

Great guide! My 11-year-old son was able to fix his Switch himself with no difficulty.

Matt - 답글

Some one can help me, when I tried to put the connector again I damage the fpc connector of the motherboard so I try to find out again can any one know the kind of model of this connector I really appreciate the help

Best regards

Philip Milian - 답글

댓글 쓰기

조회 통계:

24 시간 전: 125

7일 전: 824

30일 전: 3,801

전체 시간: 188,100