주요 콘텐츠로 건너뛰기

소개

This guide shows a step by step guide to fully access the keyboard, to clean it if it is sticking or completely replace the keypad if it is broken.

  1. Using the thumbtab molded on the bottom of the phone, pry the back cover off using either a fingernail or a plastic opening tool. Using the thumbtab molded on the bottom of the phone, pry the back cover off using either a fingernail or a plastic opening tool.
    • Using the thumbtab molded on the bottom of the phone, pry the back cover off using either a fingernail or a plastic opening tool.

  2. There is a molded notch in the white frame of the phone near the top right of the battery.  Using either a finger or a plastic opening tool, utilize the notch to lift up on the battery, and remove it from the device. This specific device did not come with a battery.
    • There is a molded notch in the white frame of the phone near the top right of the battery. Using either a finger or a plastic opening tool, utilize the notch to lift up on the battery, and remove it from the device.

    • This specific device did not come with a battery.

  3. Skip the upgrade.

    Take $10 off $50 with
    SKIPANDSAVE10

    Save Now

    Skip the upgrade.

    Take $10 off $50 with
    SKIPANDSAVE10

    Save Now
  4. Using a T5 screwdriver bit, remove the (6) 5.0 mm screws along the outside edge of the frame. Using a metal spudger, wedge the 6 plastic tabs molded into the outer shell away from the frame to lift up and remove it. Using a metal spudger, wedge the 6 plastic tabs molded into the outer shell away from the frame to lift up and remove it.
    • Using a T5 screwdriver bit, remove the (6) 5.0 mm screws along the outside edge of the frame.

    • Using a metal spudger, wedge the 6 plastic tabs molded into the outer shell away from the frame to lift up and remove it.

  5. Use a spudger to simultaneously leverage the shell away and the motherboard up from the body of the shell. Use a spudger to simultaneously leverage the shell away and the motherboard up from the body of the shell. Use a spudger to simultaneously leverage the shell away and the motherboard up from the body of the shell.
    • Use a spudger to simultaneously leverage the shell away and the motherboard up from the body of the shell.

  6. Using a spudger, unclip the bottom left snap to unplug the keyboard.  The image shows the motherboard rotated 90 degrees counterclockwise Using a spudger, unclip the bottom left snap to unplug the keyboard.  The image shows the motherboard rotated 90 degrees counterclockwise Using a spudger, unclip the bottom left snap to unplug the keyboard.  The image shows the motherboard rotated 90 degrees counterclockwise
    • Using a spudger, unclip the bottom left snap to unplug the keyboard. The image shows the motherboard rotated 90 degrees counterclockwise

  7. Using your thumb, push the tab on the right side of the motherboard over to the right and then push downward to unclip the keyboard.  It should fall away.
    • Using your thumb, push the tab on the right side of the motherboard over to the right and then push downward to unclip the keyboard. It should fall away.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Aaron LeBlanc

회원 가입일: 2018년 10월 24일

486 평판

안내서 5개 작성하였습니다

UMass Dartmouth, Team S3-G3, Peak Fall 2018 UMass Dartmouth, Team S3-G3, Peak Fall 2018 회원

UMASSD-PEAK-F18S3G3

3 회원들

안내서 8개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 1

지난 7일: 10

지난 30일: 27

전체 시간: 193