기기를 고치세요

수리할 권리

부품 & 도구

Nvidia Shield Tablet Motherboard Replacement

작성자 Molly Bauer (또 다른 기여자 6명)
  • 댓글 10
  • 즐겨찾기 2
  • 완료: 6

난이도

보통

단계

7

소요 시간

40 - 50 분

섹션

2

플래그

0

소개

Use this guide to replace the motherboard in your Nvidia Shield Tablet.

  1. First, remove the stylus from your tablet. First, remove the stylus from your tablet.

    • First, remove the stylus from your tablet.

    편집

  2. Set the tablet so the buttons, microSD, and stylus port are facing you. Open the microSD slot. Using the flat end of the spudger tool, carefully pry open the case starting from the microSD slot, slowly sliding the spudger along the inside edge of the case.

    • Set the tablet so the buttons, microSD, and stylus port are facing you.

    • Open the microSD slot.

    • Using the flat end of the spudger tool, carefully pry open the case starting from the microSD slot, slowly sliding the spudger along the inside edge of the case.

    • You may want to put on your anti-static wrist strap at this point as the motherboard will be vulnerable to physical touch and electrostatic shock after the casing is removed.

    편집

  3. As you remove your case, be aware of small clips along the edges. Finally, set the old casing aside.

    • As you remove your case, be aware of small clips along the edges.

    • Finally, set the old casing aside.

    편집

  4. Nintendo Switch 키트

    게임으로 돌아가기 위한 빠른 해결책

    Nintendo Switch 키트 쇼핑하기

    Nintendo Switch 키트

    게임으로 돌아가기 위한 빠른 해결책

    Nintendo Switch 키트 쇼핑하기

  5. Carefully use the precision tweezers to unplug the ribbon cable.

    • Carefully use the precision tweezers to unplug the ribbon cable.

    • Be sure to have your anti-static wrist strap on for this procedure.

    편집

  6. Remove the two 6.5 mm Phillips #00 screws and seven 3.0 mm Phillips #00 screws. Remove the two 6.5 mm Phillips #00 screws and seven 3.0 mm Phillips #00 screws. Remove the two 6.5 mm Phillips #00 screws and seven 3.0 mm Phillips #00 screws.

    • Remove the two 6.5 mm Phillips #00 screws and seven 3.0 mm Phillips #00 screws.

    편집

  7. Use a pair of tweezers to disconnect the three black antenna cables from the motherboard. Use the flat end of the spudger tool to carefully pry up the motherboard. In the first Shield, the stylus ribbon cable is located under the right side of board. While there are 2 additional cables for the cameras underneath the left end of the board. Be sure to loosen the cameras before lifting the board.

    • Use a pair of tweezers to disconnect the three black antenna cables from the motherboard.

    • Use the flat end of the spudger tool to carefully pry up the motherboard.

    • In the first Shield, the stylus ribbon cable is located under the right side of board. While there are 2 additional cables for the cameras underneath the left end of the board. Be sure to loosen the cameras before lifting the board.

    편집

  8. Desolder the positive and negative battery cables from the motherboard. Make sure to note which wire goes where, you don't want to re-solder the wires backwards!

    • Desolder the positive and negative battery cables from the motherboard.

    • Make sure to note which wire goes where, you don't want to re-solder the wires backwards!

    • The motherboard should now come free.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 6명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 6명과 함께

Molly Bauer

회원 가입일: 2015년 08월 27일

1,336 평판

안내서 6개 작성하였습니다

배지: 22

배지 +19개 더

팀

USF Tampa, Team 2-2, Blackwell Fall 2015 USF Tampa, Team 2-2, Blackwell Fall 2015 회원

USFT-BLACKWELL-F15S2G2

3 회원들

안내서 11개 작성하였습니다

댓글 9개

의견 추가하세요

Where do you obtain a new motherboard?

imprintcave - 답글

The real question is more about how to find a new shield tablet motherboard ??

willixlive - 답글

where can i buy the motherboard

Gurjot Dhaliwal - 답글

waar kan ik een nieuw shield moederbord kopen?

tom1vangestel - 답글

Hello, I'm looking for a description of the various ribbon connectors on the motherboard.

I'm also looking for a hint to solve a problem I have after replacing the screen+digitizer: the right side (half) of the touch screen does'n work.

Laurent Zanoni - 답글

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 7

30일 전: 39

전체 시간: 7,941