기기를 수리하세요 커뮤니티 상점

ORFELD EV-660-S222 Battery LED Board Replacement

소개

If the LEDs for the battery life indicator on your ORFELD EV-660 have gone out, it can make it impossible to tell how much charge you have left and how long you can continue to vacuum for. Make sure to exercise caution when desoldering wires.

필요한 것

  1. ORFELD EV-660-S222 Battery LED Board Replacement, Battery LED Board: 1 단계, 이미지 1/1

    • Separate the dust cover and the motor from the vacuum body by pressing the eject button.

    편집

  2. ORFELD EV-660-S222 Battery LED Board Replacement: 2 단계, 이미지 1/2 ORFELD EV-660-S222 Battery LED Board Replacement: 2 단계, 이미지 2/2

    • Place the vacuum on its side, with the screws facing towards you.

    • Remove the 11.5 mm screws using a Phillips #1 screwdriver.

    편집

  3. ORFELD EV-660-S222 Battery LED Board Replacement: 3 단계, 이미지 1/2 ORFELD EV-660-S222 Battery LED Board Replacement: 3 단계, 이미지 2/2
    이 단계에 사용된 도구:
    Tweezers
    $4.99
    구매

    • Using tweezers, remove the sticker connecting the two halves.

    • Use the opening pick to gently separate the top half and the bottom half of the vacuum.

    • Press the blue buttons near the sides of the battery LEDs to remove the top half.

    편집

  5. ORFELD EV-660-S222 Battery LED Board Replacement: 4 단계, 이미지 1/2 ORFELD EV-660-S222 Battery LED Board Replacement: 4 단계, 이미지 2/2

    • Slide out the charging port.

    편집

  6. ORFELD EV-660-S222 Battery LED Board Replacement: 5 단계, 이미지 1/1

    • Lift the battery slightly to reveal the pin connectors.

    • Gently disconnect the six-pin connector that connects to the power button and battery LEDs.

    편집

  7. ORFELD EV-660-S222 Battery LED Board Replacement: 6 단계, 이미지 1/3 ORFELD EV-660-S222 Battery LED Board Replacement: 6 단계, 이미지 2/3 ORFELD EV-660-S222 Battery LED Board Replacement: 6 단계, 이미지 3/3

    • Slide out the battery LEDs from the compartment.

    • Remove the plastic LED cover from the LED board.

    편집

  8. ORFELD EV-660-S222 Battery LED Board Replacement: 7 단계, 이미지 1/1

    • Desolder the LED board from the wires.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 3명과 함께

Sarthak Shrestha

회원 가입일: 09/12/23

441 평판

안내서 3개 작성하였습니다

배지: 6

배지 +3개 더

팀

University of North Texas, Team 2-4, Harold Fall 2023 University of North Texas, Team 2-4, Harold Fall 2023 회원

UNT-HAROLD-F23S2G4

4 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 6

30일 전: 19

전체 시간: 180