소개

This Guide will give step-by-step instructions on how to install a microphone and speaker system into the Olympus D590 camera.

  1. Flip camera so you are looking at the bottom.
    • Flip camera so you are looking at the bottom.

    • Unscrew all 5 base plate screws.

    댓글 쓰기

  2. Lift open retainer clip by sliding the clip to the left and letting the clip pop up.
    • Lift open retainer clip by sliding the clip to the left and letting the clip pop up.

    댓글 쓰기

    • Unscrew the single screw located next to the battery slot.

    댓글 쓰기

    • Turn the camera so that the USB, AV and DC in/out rubber plate it facing you.

    • Lift the rubber plate exposing the ports beneath.

    댓글 쓰기

    • Unscrew the 2 screws next to the USB and AC ports.

    댓글 쓰기

    • Use a flathead screwdriver or another flat opening tool to pry the faceplate from the whole device.

    댓글 쓰기

    • Pull off the faceplate to reveal the inside of the camera.

    • Be careful of the connector that goes from the faceplate to the motherboard . Disconnecting this line will cause the camera not not power on through the on/off switch anymore.

    댓글 쓰기

    • Use a phillips head screwdriver to remove the 3 screws highlighted in the picture.

    댓글 쓰기

    • Unscrew the 2 screws located on either side of the flash.

    댓글 쓰기

    • Get a flathead screwdriver or an iPod opening tool (both are shown in this picture).

    • Carefully pry off the blackplate from the remaining part of the camera.

    댓글 쓰기

    • Pull the backplate off.

    댓글 쓰기

    • Unscrew the screw shown in the picture from LCD screen.

    댓글 쓰기

    • Remove the side pannel by sliding it off the body of the camera.

    • Lift the camera no more than 3cm to make sure all screws have been taken off.

    댓글 쓰기

    • Flip camera so you are looking at the front.

    • Remove gray and blue wiring with tweasers by gently wiggling and pulling.

    • Be careful not to rip the wiring tape with the tweezers.

    댓글 쓰기

    • Locate the tape securing the wiring with the gray end piece located on top of the camera.

    • Gently lift up on the tape till all wires are exposed.

    댓글 쓰기

    • Flip Camera to the bottom side as shown.

    • Pull and wriggle the thin yellow wiring tape to detach it from the rest of the camera, while leaving it attached to the LCD screen.

    댓글 쓰기

    • Flip camera so the front is facing you.

    • Locate speaker in upper right hand corner.

    • Gently lift with tweasers.

    • Feed wiring through designated spot so that it is no longer connected to the camera.

    댓글 쓰기

    • Lift the LCD screen so the thick yellow wiring is the only thing attaching the LCD screen to the camera.

    • Gently pull the thick yellow wiring out by using the forefinger and thumb.

    댓글 쓰기

    • Locate speaker on the back of the LCD screen.

    • Remove the tape holding the speaker down by lifing with tweesers.

    • Remove speaker from holding dock.

    댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

Joshua

회원 가입일: 2010년 04월 15일

7 평판

안내서 2개 작성하였습니다

Cal Poly, Team 28-23, Regan Spring 2010 Cal Poly, Team 28-23, Regan Spring 2010 회원

CPSU-REGAN-S10S28G23

4 회원들

안내서 7개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 0

전체 시간: 1,326