난이도
보통
단계
19
소요 시간
10 - 15 분
- Case 7 단계
- Lens 3 단계
- Logic Board 4 단계
- Flash 5 단계
마크업 사고
해당 안내서는 더 나은 마크업이 필요합니다. 일부 마크업 주석의 편집 또는 작성을 도와주십시오!
한 단계 누락
이런! 해당 안내서는 현재 몇몇 중요한 단계가 빠져 있습니다.
부품
부품은 필요하지 않습니다.
-
Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws)
-
Remove the right side panel by pulling off the large silver piece.
There is no reference to removing screws from the right side panel, where it is necessary to remove 2 screws to do so.
-
Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws)
-
Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece. (2 pieces)
-
Remove the black front panel by sliding it towards the lens and then pulling it up off the camera.
-
Remove 3 screws from the front of the camera using a #00 screwdriver.
-
Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side)
Wrong point of focus for the second picture. What should be in focus is very blurry.
-
Using a plastic spudger, lift up the black clips.
-
Still using the plastic spudger, detach the gold connector strip and white connector strip.
-
Using both hands, pull the camera apart into two pieces.
There were multiple gold strips, so the one that needs to be pulled should be highlited in the picture.
in step seven pull up the black bar of the ZIF connectors before pulling out the white or gold ribbons
-
Using a plastic spudger, lift up the black clips.
-
Still using the spudger, detach the 3 gold wire tape connectors from the inside of the camera.
-
Remove 3 screws from the inside of the camera using a #00 screwdriver.
-
Using your thumb and forefinger, pull the lens piece straight out from the body of the camera.
-
Unscrew two screws on the right side of the camera using a #00 screwdriver.
-
Using a plastic spudger, lift up the black clips.
-
Still using the spudger, detach the gold wire tape connectors from the logic board.
-
Unsolder the upper right and lower left wires to remove logic board.
-
In order to remove the logic board, grab each side of it and pull up using your thumb and forefinger.
-
Unscrew 2 screws using a #00 screwdriver.
-
Now lift the metal piece straight up in order to remove it.
-
Pull on the white tab to remove the small logic board with the flash on it.
-
Pull out sliver button using your thumb and forefinger.
-
Now remove small logic board out of camera casing.
-
Remove plastic flash cover using a spudger.
-
Remove the flash bulb using a plastic spudger.
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
팀
Cal Poly, Team 13-4, Forte Winter 2011 Cal Poly, Team 13-4, Forte Winter 2011 회원
CPSU-FORTE-W11S13G4
6 회원들
안내서 6개 작성하였습니다
Put a notice on here that the screws are very small and are easy to misplace while disassembling device. Also, while disassembling the device there was only one screw present, where the guide suggested there were three.
Curtis Reedy - 답글
Before beginning, put a note that the camera should be turned off before proceeding.
Curtis Reedy - 답글
Add a note at the beginning of the guide that there are a large number of small screws that should be separated as the steps are completed.
Curtis Reedy - 답글
There's a capacitor .....watch out for it in every step.
BILL BOYD - 답글