주요 콘텐츠로 건너뛰기

기기를 수리하세요

수리할 권리

상점

소개

This guide will allow you to remove the screen from the inside of the device in order to clean it or replace it. The screen on a device can easily crack. This repair is easy to do and does not require any special tools.

  1. Ensure device is powered off before disassembly. Remove the 4 rubber screw plugs using a spudger. Remove the 4 rubber screw plugs using a spudger.
    • Ensure device is powered off before disassembly.

    • Remove the 4 rubber screw plugs using a spudger.

  2. Remove the four 4.8mm mounting screws using a PH00 screwdriver. Remove the four 4.8mm mounting screws using a PH00 screwdriver. Remove the four 4.8mm mounting screws using a PH00 screwdriver.
    • Remove the four 4.8mm mounting screws using a PH00 screwdriver.

  3. Starting at one corner, gently pry the back panel assembly from the screen assembly using two plastic opening tools. Slide the opening tools around the perimeter of the device to separate the back panel assembly from the screen assembly.
    • Starting at one corner, gently pry the back panel assembly from the screen assembly using two plastic opening tools.

    • Slide the opening tools around the perimeter of the device to separate the back panel assembly from the screen assembly.

  4. Gently lift the screen assembly away from the back cover assembly. Be careful when separating the two pieces as the screen assembly is still connected to the mother board by two ribbon cables.
    • Gently lift the screen assembly away from the back cover assembly.

    • Be careful when separating the two pieces as the screen assembly is still connected to the mother board by two ribbon cables.

  5. Disconnect the two ribbon connectors by flipping the gray tabs up with a fingernail or a spudger. Remove the ribbon cables. Remove the ribbon cables.
    • Disconnect the two ribbon connectors by flipping the gray tabs up with a fingernail or a spudger.

    • Remove the ribbon cables.

  6. Remove all 14 of the 3.6mm screws using a PH00 screwdriver. Remove all 14 of the 3.6mm screws using a PH00 screwdriver. Remove all 14 of the 3.6mm screws using a PH00 screwdriver.
    • Remove all 14 of the 3.6mm screws using a PH00 screwdriver.

  7. Gently separate the screen from the plastic border/screen holder by pulling it off with your hands. Gently separate the screen from the plastic border/screen holder by pulling it off with your hands. Gently separate the screen from the plastic border/screen holder by pulling it off with your hands.
    • Gently separate the screen from the plastic border/screen holder by pulling it off with your hands.

  8. Remove the grey monitor from the glass screen cover by gently lifting it up. Remove the grey monitor from the glass screen cover by gently lifting it up. Remove the grey monitor from the glass screen cover by gently lifting it up.
    • Remove the grey monitor from the glass screen cover by gently lifting it up.

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

William Sioholm

회원 가입일: 2015년 03월 11일

104 평판

안내서 1개 작성함

Colorado Springs, Team 4-6, Panko Spring 2015 Colorado Springs, Team 4-6, Panko Spring 2015 회원

UCCS-PANKO-S15S4G6

3 회원들

안내서 10개 작성하였습니다

بدي من هي الشاشة وين بلاقي

abdurrhman khrrat - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 4

30일 전: 5

전체 시간: 374