기기를 수리하세요 커뮤니티 상점

Oster BLSTSS-PZO Power Cord Replacement

소개

The power cord is responsible for providing power to your device. This guide will instruct you on how to replace the power cord.

필요한 것

  1. Oster BLSTSS-PZO Power Cord Replacement, Circuitboard: 1 단계, 이미지 1/1

    • Use the prying tools to open the four plastic screw holes on the bottom of the blender.

    편집

  2. Oster BLSTSS-PZO Power Cord Replacement: 2 단계, 이미지 1/1

    • Use the Phillips #1 Screwdriver to unscrew the four 16 mm screws and remove the plastic bottom.

    편집

  3. Oster BLSTSS-PZO Power Cord Replacement: 3 단계, 이미지 1/1

    • Gently remove the circuit board.

    편집

  5. Oster BLSTSS-PZO Power Cord Replacement: 4 단계, 이미지 1/2 Oster BLSTSS-PZO Power Cord Replacement: 4 단계, 이미지 2/2

    • Use the spudger to detach the black wire from the circuit board.

    • Repeat for yellow wire.

    편집

  6. Oster BLSTSS-PZO Power Cord Replacement: 5 단계, 이미지 1/3 Oster BLSTSS-PZO Power Cord Replacement: 5 단계, 이미지 2/3 Oster BLSTSS-PZO Power Cord Replacement: 5 단계, 이미지 3/3

    • Use the Phillips #1 to remove the four 8mm screws.

    • Use the medal spudger to detach the circuit board from the buttons.

    • Gently pull and release circuit board from buttons.

    편집

  7. Oster BLSTSS-PZO Power Cord Replacement, Power Cord: 6 단계, 이미지 1/3 Oster BLSTSS-PZO Power Cord Replacement, Power Cord: 6 단계, 이미지 2/3 Oster BLSTSS-PZO Power Cord Replacement, Power Cord: 6 단계, 이미지 3/3

    • Locate petal prong on the end of the power cord.

    • Bend metal prong until it's straight with your finger.

    편집

  8. Oster BLSTSS-PZO Power Cord Replacement: 7 단계, 이미지 1/2 Oster BLSTSS-PZO Power Cord Replacement: 7 단계, 이미지 2/2

    • Spring will pop out when you pull out metal prong

    • Pull prong out of the hole.

    편집

  9. Oster BLSTSS-PZO Power Cord Replacement: 8 단계, 이미지 1/3 Oster BLSTSS-PZO Power Cord Replacement: 8 단계, 이미지 2/3 Oster BLSTSS-PZO Power Cord Replacement: 8 단계, 이미지 3/3

    • Pinch plastic prongs on base of blender to remove plastic securing device.

    • Remove plastic securing device.

    • Pull power cord out of blender base.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 1명과 함께

Loren Hyer

회원 가입일: 09/20/17

101 평판

안내서 1개 작성함

배지: 4

+1개 배지 추가

팀

University of North Texas, Team S7-G8, Thomas Fall 2017 University of North Texas, Team S7-G8, Thomas Fall 2017 회원

UNT-THOMAS-F17S7G8

3 회원들

안내서 4개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 3

30일 전: 5

전체 시간: 194