기기를 수리하세요 커뮤니티 상점

Oster Expressbake CKSTBRTW20 Heating Coils Replacement

소개

The heating coils may get dirty or in operable with use. This guide will show how to remove the heating coils in order to properly replace or clean them. Prior to replacing the heating coils, ensure that the heating problem is not caused by electrical errors as discussed in the troubleshooting page.

필요한 것

  1. Oster Expressbake CKSTBRTW20 Heating Coils Replacement, Top Panel Removal: 1 단계, 이미지 1/1

    • Remove the bread pan.

    번역하기

  2. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 2 단계, 이미지 1/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 2 단계, 이미지 2/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 2 단계, 이미지 3/3

    • Remove the eight 22mm Phillips #1 screws from the grey lining.

    • Remove the grey liner.

    번역하기

  3. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 3 단계, 이미지 1/2 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 3 단계, 이미지 2/2

    • Remove the two 11mm Phillips #1 screws from the back of the device.

    번역하기

  4. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 4 단계, 이미지 1/2 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 4 단계, 이미지 2/2

    • Pop off the top case using a spudger.

    • Keep the spudger away from the control panel.

    • Be aware of wires connecting the microcontroller to the panel when removing the top lining.

    번역하기

  5. Oster Expressbake CKSTBRTW20 Heating Coils Replacement, Inner Chamber: 5 단계, 이미지 1/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement, Inner Chamber: 5 단계, 이미지 2/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement, Inner Chamber: 5 단계, 이미지 3/3

    • Disconnect microcontroller and top lining.

    • Ground yourself prior to disconnecting in order to avoid harming the inner electronics.

    번역하기

  7. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 6 단계, 이미지 1/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 6 단계, 이미지 2/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 6 단계, 이미지 3/3

    • Remove the four 11mm Phillips #1 screws holding from the guard and inner lining.

    • Remove small rectangular guard from bottom of liner

    번역하기

  8. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 7 단계, 이미지 1/1

    • Remove the inner liner.

    • The inner liner will be connected to the outer chamber with wires.

    번역하기

  9. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 8 단계, 이미지 1/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 8 단계, 이미지 2/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 8 단계, 이미지 3/3

    • Disconnect the red wires from the inner liner.

    번역하기

  10. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 9 단계, 이미지 1/2 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 9 단계, 이미지 2/2

    • Remove the single 11mm Phillips #1 screw thats holding and inner lining in place.

    번역하기

  11. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 10 단계, 이미지 1/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 10 단계, 이미지 2/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 10 단계, 이미지 3/3

    • Use a spudger to push out the connector found on the inner lining.

    번역하기

  12. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 11 단계, 이미지 1/2 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 11 단계, 이미지 2/2

    • Remove lining.

    번역하기

  13. Oster Expressbake CKSTBRTW20 Heating Coils Replacement, Heating Coils: 12 단계, 이미지 1/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement, Heating Coils: 12 단계, 이미지 2/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement, Heating Coils: 12 단계, 이미지 3/3

    • Remove the two 11mm Phillips #1 screws from the inside of the chamber.

    • Removal of the screws may also require a 1/4 socket wrench on the other side to prevent spinning.

    번역하기

  14. Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 13 단계, 이미지 1/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 13 단계, 이미지 2/3 Oster Expressbake CKSTBRTW20 Heating Coils Replacement: 13 단계, 이미지 3/3

    • Remove the 11mm Phillips #1 screw from the heating coil.

    • After you have removed the screw the coils will pop out of place.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 2명과 함께

Megan Saunders

회원 가입일: 01/25/18

701 평판

안내서 5개 작성하였습니다

배지: 10

배지 +7개 더

팀

USF Tampa, Team S7-G5, Passmore Spring 2018 USF Tampa, Team S7-G5, Passmore Spring 2018 회원

USFT-PASSMORE-S18S7G5

4 회원들

안내서 5개 작성하였습니다

댓글 한 개

We odered a new element but when we took the maker apart one of the leads was not attached. The maker had “walked” off our slick countertop and we think that is when the lead came off. We cleaned the felt pads and put silicone pads on top of those and now it stays stationary. Thank you for this tutorial. Love being able to fix things instead of tossing them. We have repaired our dishwasher twice and even the microwave. Freedom to repair is vital.

Laurie L Sippel - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 4

30일 전: 7

전체 시간: 471