소개

This will remove the circuit board from the front portion of the phone to reveal the keyboard and screen.

부품

부품은 필요하지 않습니다.

  1. Press the button on the back cover to release the battery cover.
    • Press the button on the back cover to release the battery cover.

    • Slide off the battery cover.

    댓글 쓰기

  2. Remove the battery by lifting up on one side.
    • Remove the battery by lifting up on one side.

    댓글 쓰기

    • Remove the stylus by pulling up on the large top to reveal the top left case screw.

    • Pull away the black flap to reveal the top right case screw.

    댓글 쓰기

    • WARNING: The top right red screw marked by the red circle has a warranty seal. Removing this seal will void your warranty.

    • Use the T5 screwdriver attachment to remove the 5 black back case screws marked by the red and yellow circles. These screws are 0.274 inches long.

    • Use the same T5 screwdriver attachment to remove the middle screw marked by the blue circle. It is shorter than the other screws at 0.121 inches in length.

    댓글 쓰기

    • Use the plastic opening tool to pry open the device. Start on the volume control side (left side of the screen) and work your way up along the edge and across the top.

    • ATTENTION: Side volume control buttons may fall out after opening the device.

    댓글 쓰기

  3. Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    Fixmas/픽스마스 분위기를 띄우세요
    FIXMAS12 코드로 $50 이상 구매시 $12 할인을 받으십시오
    • Slowly unfold the back casing away from the front casing revealing the red and black wound wire speaker cable, marked by the yellow box.

    • WARNING: Be gentle while separating the halves to prevent breaking the red and black wound wire speaker cable that bridges both halves.

    댓글 쓰기

    • Using tweezers, squeeze the plastic head of the black and red wound wire cable. This will detach the cable from the circuit board and fully separate the two halves.

    댓글 쓰기

    • Gently peel off the protective yellow tape covering the ribbon cable using tweezers or your fingers.

    • ATTENTION: Save the tape for reassembly.

    댓글 쓰기

    • Using tweezers flip up the black plastic snap covering the small ribbon cable.

    • Using tweezers gently pull out the ribbon cable to detach it from the circuit board.

    댓글 쓰기

    • With the screen facing down. Use the Phillips 00 screwdriver attachment to remove the silver, 0.124 inch long screw on the left side of the circuit board above the ribbon cable.

    • WARNING: Do not over-tighten the screw during reassembly.

    댓글 쓰기

    • Pivot the circuit board away from the casing keeping the screen face down.

    • Gently peel away the tape holding the ribbon cable to the screen.

    • ATTENTION: Save the tape for reassembly.

    댓글 쓰기

    • Using tweezers flip up the black plastic snap covering the ribbon cable attached to the screen.

    • Gently pull out the ribbon cable freeing the circuit board from the casing.

    댓글 쓰기

    • Separate the circuit board from front cover.

    댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

다른 한 분이 해당 안내서를 완성하였습니다.

Mike Shaw

회원 가입일: 2011년 01월 03일

601 평판

안내서 6개 작성하였습니다

Cal Poly, Team 14-6, Forte Winter 2011 Cal Poly, Team 14-6, Forte Winter 2011 회원

CPSU-FORTE-W11S14G6

6 회원들

안내서 12개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 1

전체 시간: 1,794