주요 콘텐츠로 건너뛰기

소개

This guide will show you how to access the front frame of the camera. This is the area of the camera that contains buttons like the playback and cursor buttons, as well as the window through which you can view the LCD screen. If these buttons have come loose, or if the frame is cracked, this guide will help you replace the frame. Before you begin, make sure that the battery and SD card have been removed.

  1. All screws should be removed using a Phillips #0 screwdriver. Using your screwdriver, unscrew the two 5.0 mm Philips screws to the right of the LCD screen.
    • All screws should be removed using a Phillips #0 screwdriver.

    • Using your screwdriver, unscrew the two 5.0 mm Philips screws to the right of the LCD screen.

  2. Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there. Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there.
    • Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there.

  3. Turn the camera upside down and  unscrew the three 5mm screws found on the bottom. Turn the camera upside down and  unscrew the three 5mm screws found on the bottom.
    • Turn the camera upside down and unscrew the three 5mm screws found on the bottom.

  4. On the top of the camera  locate the two rails with a thin sheet of metal on the floor between them. With a metal spudger, lift this sheet and push it out of the rail device to detach it from the camera.
    • On the top of the camera locate the two rails with a thin sheet of metal on the floor between them.

    • With a metal spudger, lift this sheet and push it out of the rail device to detach it from the camera.

  5. Proceed to remove the four 5mm Phillips screws that you just uncovered.
    • Proceed to remove the four 5mm Phillips screws that you just uncovered.

  6. Slowly pull on both side of the camera, until both halves begin to separate from each other.
    • Slowly pull on both side of the camera, until both halves begin to separate from each other.

    • Do not pull too hard, as both halves are held together with ZIF connector cables.

  7. Using a plastic opening tool, carefully flip up the small black levers that attach the ribbon cables to the ZIF connectors on the motherboard. Carefully pull the ribbon cables out of the slot once they have been released. Only the two indicated connectors need to be removed to separate the two halves of the camera.
    • Using a plastic opening tool, carefully flip up the small black levers that attach the ribbon cables to the ZIF connectors on the motherboard.

    • Carefully pull the ribbon cables out of the slot once they have been released.

    • Only the two indicated connectors need to be removed to separate the two halves of the camera.

  8. Unscrew the five 5mm screws on the panel that you just removed. Unscrew the five 5mm screws on the panel that you just removed.
    • Unscrew the five 5mm screws on the panel that you just removed.

  9. Remove the entire silver panel to reveal the back of the LCD screen Remove the entire silver panel to reveal the back of the LCD screen
    • Remove the entire silver panel to reveal the back of the LCD screen

  10. Remove the LCD screen.
    • Remove the LCD screen.

  11. You can now access the back panel and the buttons on it.
    • You can now access the back panel and the buttons on it.

  12. To remove a button, lightly press its front face and it should detach with ease.
    • To remove a button, lightly press its front face and it should detach with ease.

    • To put a button back into the camera, press on front its back face until it snaps back on.

결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

Emily Kuzmicky

회원 가입일: 2017년 01월 24일

381 평판

안내서 2개 작성하였습니다

Cal Poly, Team 21-3, Maness Winter 2017 Cal Poly, Team 21-3, Maness Winter 2017 회원

CPSU-MANESS-W17S21G3

6 회원들

안내서 12개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 9

전체 시간: 588