소개

This guide will take you through the steps of removing the touchscreen.

Locate the bay door for the battery on the left side of the laptop.
  • Locate the bay door for the battery on the left side of the laptop.

댓글 쓰기

Slide the latch to the right and then down to unlock it. Pull out the battery.
  • Slide the latch to the right and then down to unlock it.

  • Pull out the battery.

댓글 쓰기

Remove the four hinge screws from the back of the computer.
  • Remove the four hinge screws from the back of the computer.

댓글 쓰기

Open the laptop and remove the four indicated screws with a Phillips size 0 screwdriver. Pry off the plastic strip which was previously held in place by the screws.
  • Open the laptop and remove the four indicated screws with a Phillips size 0 screwdriver.

  • Pry off the plastic strip which was previously held in place by the screws.

댓글 쓰기

Remove the four hinge screws to allow the hinges to rotate up and move.
  • Remove the four hinge screws to allow the hinges to rotate up and move.

댓글 쓰기

Mac RAM 키트
Mac 속도를 높이십시오. 메모리를 최대한 활용하십시오.
Mac RAM 키트
Mac에서 메모리를 더 많이 확보하십시오.
Remove 16 screws from the top of the closed laptop.
  • Remove 16 screws from the top of the closed laptop.

    • 12 Phillips size 1 screws

    • 2 Phillips size 0 screws

    • 2 Torx size 6 screws (T6)

I found that the Torx screw on my model to be T8.

Harley - 답글

Is the touchscreen & the LCD 1 piece? or are they separate?

Chasity Miller -

Gently break the adhesive seal between the front and rear display cases with a plastic opening tool.
  • Gently break the adhesive seal between the front and rear display cases with a plastic opening tool.

    • You will need to reapply the silicon adhesive during reassembly to ensure watertight seal.

댓글 쓰기

Pull the top halve of the casing up revealing the inside of the screen
  • Pull the top halve of the casing up revealing the inside of the screen

댓글 쓰기

The top half of the case can be removed by sliding the tabs out from under the hinges. This makes unplugging the screen wiring much easier
  • The top half of the case can be removed by sliding the tabs out from under the hinges.

    • This makes unplugging the screen wiring much easier

댓글 쓰기

There are 4 wires that need to be unplugged to remove the screen.
  • There are 4 wires that need to be unplugged to remove the screen.

댓글 쓰기

For the first wire, peel back the silver cover tape to reveal the connection.
  • For the first wire, peel back the silver cover tape to reveal the connection.

댓글 쓰기

Pull the wiring away from the connection to release it.
  • Pull the wiring away from the connection to release it.

댓글 쓰기

Remove the 3 strips of black tape as shown to reveal connections 2 and 3.
  • Remove the 3 strips of black tape as shown to reveal connections 2 and 3.

  • Pull the wiring for each away from the connections to remove.

댓글 쓰기

The 4th connection is already visible.
  • The 4th connection is already visible.

    • Depending on your model it might not be plugged into anything. If it is, remove it the same way the other 3 connections were removed.

댓글 쓰기

Using a plastic opening tool, lift the screen as shown from the case and pull free. Using a plastic opening tool, lift the screen as shown from the case and pull free.
  • Using a plastic opening tool, lift the screen as shown from the case and pull free.

댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

다른 5명이 해당 안내서를 완성하였습니다.

Dylan Bloom

회원 가입일: 2010년 04월 12일

262 평판

안내서 4개 작성하였습니다

Cal Poly, Team 27-93, Amido Spring 2010 Cal Poly, Team 27-93, Amido Spring 2010 회원

CPSU-AMIDO-S10S27G93

4 회원들

안내서 12개 작성하였습니다

This guide is good for replacing the LCD screen, but it is not complete for the touchscreen panel, which requires some more delicate and precise steps. I think the title of the guide needs to be changed.

Thanks

Alessandro Cervelli - 답글

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 8

지난 30일: 35

전체 시간: 15,174