기기를 수리하세요 커뮤니티 상점

Philips BiPAP S/T Air Filter Replacement

의료 장비
iFixit과 이 수리 안내서는 의료 기기 제조업체가 보증하지 않으며 제휴 관계가 없습니다.

소개

A dirty inlet filter may cause high operating temperatures that may affect device performance. Under normal usage, the foam filter should be cleaned at least once every two weeks and replaced with a new one every six months. This guide can be done effortlessly and just requires your two hands.

The video below details air filter replacements for CPAP and BiPAP machines. Although this is not specifically the BiPAP S/T device, it can be used as an aid for better understanding.

For more information on replacing the air filter in the ventilator, please refer to page 6-27 in the service manual.

동영상 개요

  1. Philips BiPAP S/T Air Filter Replacement, Air Filter: 1 단계, 이미지 1/1

    • Disconnect the device from the power source to stop airflow.

    • To avoid electrical shock, always unplugged the power cord from the wall outlet before cleaning the device.

    번역하기

  2. Philips BiPAP S/T Air Filter Replacement: 2 단계, 이미지 1/2 Philips BiPAP S/T Air Filter Replacement: 2 단계, 이미지 2/2

    • Remove the filter from the enclosure by gently squeezing the filter in the center and pulling it away from the device.

    번역하기

    • Examine the filter for cleanliness and quality.

    • If the foam filter is torn, replace it. (Only Philips Respironics-supplied filters should be used as replacement filters.)

    • A dirty inlet filter may cause high operating temperatures that may affect device performance. Regularly examine the inlet filter.

    번역하기

  4. Philips BiPAP S/T Air Filter Replacement: 4 단계, 이미지 1/1

    • Wash the gray foam filter in warm water with a mild detergent.

    • Rinse thoroughly to remove all detergent residue.

    • Allow the filter to air dry completely before reinstalling it.

    • Never install a wet filter into the device. You must ensure sufficient drying time.

    번역하기

  5. Philips BiPAP S/T Air Filter Replacement: 5 단계, 이미지 1/1

    • Reinstall the filter.

    • To install, insert gray foam filter into the filter area.

    • A properly installed, undamaged filter is required for proper operation.

    번역하기
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 1명과 함께

Sophia James

회원 가입일: 04/07/20

193 평판

안내서 1개 작성함

배지: 5

배지 +2개 더

팀

Cal Poly, Team S7-G3, Paton Spring 2020 Cal Poly, Team S7-G3, Paton Spring 2020 회원

CPSU-PATON-S20S7G3

3 회원들

안내서 3개 작성하였습니다

댓글 2개

In India corona virus control in a earlier situation and now its spread in many countries again '''bipap machines''' are necessary for many peoples in this situation but you have to be careful from your side as well btw thanks for informative article.

mers - 답글

Why is there a gray blue material coming out on the output filter. It has been doing for over two years. Is it killing me. My bi pa was recalled over a year ago, when are they going to replace it ?

EDward Stone - 답글

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 6

30일 전: 20

전체 시간: 1,309