주요 콘텐츠로 건너뛰기

Philips Senseo II 7810 HD Water Level Sensor Magnet

필요한 것

  1. Philips Senseo II 7810 HD Water Level Sensor Magnet, Water Level Sensor Magnet: 1 단계, 이미지 1/2 Philips Senseo II 7810 HD Water Level Sensor Magnet, Water Level Sensor Magnet: 1 단계, 이미지 2/2
    • Pull the water tank off the machine.

  2. Philips Senseo II 7810 HD Water Level Sensor Magnet: 2 단계, 이미지 1/2 Philips Senseo II 7810 HD Water Level Sensor Magnet: 2 단계, 이미지 2/2
    • Lift off the small lid on top of the water tank.

    • The magnet in the float bowl can be seen from above.

    • The float is secured by a metal clip.

  3. Philips Senseo II 7810 HD Water Level Sensor Magnet: 3 단계, 이미지 1/3 Philips Senseo II 7810 HD Water Level Sensor Magnet: 3 단계, 이미지 2/3 Philips Senseo II 7810 HD Water Level Sensor Magnet: 3 단계, 이미지 3/3
    • Use needle nose pliers to pull out the clip.

    • The water tank is very narrow, so it takes effort and patience to get to the clip. The clip may break, then you will have to secure the magnet later, e.g. with a dab of hot glue.

  4. Philips Senseo II 7810 HD Water Level Sensor Magnet: 4 단계, 이미지 1/3 Philips Senseo II 7810 HD Water Level Sensor Magnet: 4 단계, 이미지 2/3 Philips Senseo II 7810 HD Water Level Sensor Magnet: 4 단계, 이미지 3/3
    • Open the flap on the magnet with a small flat head screwdriver.

    • The completely corroded magnet becomes visible.

    • On some models, the float looks like the third picture, but the repair is the same.

    • Float

    • Metal clip

    • Corroded magnet

  5. Philips Senseo II 7810 HD Water Level Sensor Magnet: 5 단계, 이미지 1/2 Philips Senseo II 7810 HD Water Level Sensor Magnet: 5 단계, 이미지 2/2
    • Remove the magnet with the flat head screwdriver.

    • Thoroughly clean the case of all traces of rust. Pull out the two pieces of foam rubber on the left and right side and clean them.

  6. Philips Senseo II 7810 HD Water Level Sensor Magnet: 6 단계, 이미지 1/3 Philips Senseo II 7810 HD Water Level Sensor Magnet: 6 단계, 이미지 2/3 Philips Senseo II 7810 HD Water Level Sensor Magnet: 6 단계, 이미지 3/3
    • Here is the new neodymium magnet. Its diameter must be 6 mm, height 6 - 7 mm

  7. Philips Senseo II 7810 HD Water Level Sensor Magnet: 7 단계, 이미지 1/2 Philips Senseo II 7810 HD Water Level Sensor Magnet: 7 단계, 이미지 2/2
    • Insert the magnet and the two pieces of foam rubber. Close the float bowl.

    • The case is marked "UP". This side naturally points upwards.

    • Insert the magnet with the float.

    • Put the metal clip back on, unfortunately that's pretty tricky. Long tweezers will help.

결론

Follow the steps in reverse order to reassemble your device.

다른 5명이 해당 안내서를 완성하였습니다.

다음 번역가들에게 특별히 감사 드립니다:

de en

100%

이 번역자 분들은 저희가 세상을 수리하는데 동참해 주시는 분입니다! 기여하시겠습니까?
번역 시작하기 ›

VauWeh

회원 가입일: 10/19/15

203,346 평판

안내서 246개 작성하였습니다

Repair is War on Entropy Repair is War on Entropy 회원

Community

25 회원들

안내서 1,121개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 15

7일 전: 112

30일 전: 446

전체 시간: 6,716