기기를 수리하세요

수리할 권리

상점

PlayStation 2 Slimline Optical Drive Replacement

작성자 Thomas Sullivan
  • 댓글 3
  • 즐겨찾기 17
  • 완료: 20

난이도

쉬움

단계

9

소요 시간

5 - 10 분

섹션

2

플래그

1

Member-Contributed Guide

회원-기여 안내서

해당 안내서는 저희 커뮤니티의 멋진 회원께서 작성하였습니다. iFixit 직원이 관리하지 않습니다.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

  1. Disconnect all cables from the console and flip the unit over to reveal its base.

    • Disconnect all cables from the console and flip the unit over to reveal its base.

    편집

  2. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws. Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony. Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony.

    • Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws.

    • Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony.

    편집

  3. Remove all six 4.0 mm screws from the base of the unit using a #1 Phillips screwdriver. Remove all six 4.0 mm screws from the base of the unit using a #1 Phillips screwdriver. Remove all six 4.0 mm screws from the base of the unit using a #1 Phillips screwdriver.

    • Remove all six 4.0 mm screws from the base of the unit using a #1 Phillips screwdriver.

    편집

  5. Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit. Note: You may use your hands for additional force to separate the two pieces of the outer shell. Note: You may use your hands for additional force to separate the two pieces of the outer shell.

    • Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit.

    • Note: You may use your hands for additional force to separate the two pieces of the outer shell.

    편집

  6. Locate the optical drive which occupies most of the space on the right side of the unit. It can be identified by the four screws with wide-diameter heads fastening the optical drive to the motherboard. Locate the optical drive which occupies most of the space on the right side of the unit. It can be identified by the four screws with wide-diameter heads fastening the optical drive to the motherboard.

    • Locate the optical drive which occupies most of the space on the right side of the unit. It can be identified by the four screws with wide-diameter heads fastening the optical drive to the motherboard.

    편집

  7. Remove the four 4.0 mm screws using a #1 Phillips screwdriver. Remove the four 4.0 mm screws using a #1 Phillips screwdriver.

    • Remove the four 4.0 mm screws using a #1 Phillips screwdriver.

    편집

  8. Locate the three ribbon cables connecting the optical drive to the motherboard.

    • Locate the three ribbon cables connecting the optical drive to the motherboard.

    편집

  9. Gently detach the ribbon cables from the motherboard using a pair of tweezers. Note: The ribbon cable in the center must be unlocked by lifting up the black tab. Remember to push the tab down upon re-installation to secure the cable. Caution: Always remove ribbon cables by the plastic handles located on each end. Gripping a ribbon cable anywhere but the provided handles can damage the cable and render the component useless.

    • Gently detach the ribbon cables from the motherboard using a pair of tweezers.

    • Note: The ribbon cable in the center must be unlocked by lifting up the black tab. Remember to push the tab down upon re-installation to secure the cable.

    • Caution: Always remove ribbon cables by the plastic handles located on each end. Gripping a ribbon cable anywhere but the provided handles can damage the cable and render the component useless.

    편집

  10. Remove any tape fastening the cables to the motherboard and gently lift and remove the optical drive. Remove any tape fastening the cables to the motherboard and gently lift and remove the optical drive. Remove any tape fastening the cables to the motherboard and gently lift and remove the optical drive.

    • Remove any tape fastening the cables to the motherboard and gently lift and remove the optical drive.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 20명이 해당 안내서를 완성하였습니다.

작성자

Thomas Sullivan

회원 가입일: 2013년 10월 23일

2,858 평판

안내서 6개 작성하였습니다

배지: 13

배지 +10개 더

댓글 3개

의견 추가하세요

انا أريد للغة عربية

Muammar lmgaroush - 답글

you also must disconnect the ribbon cable from the laser assembly by flipping back the little brown lever and removing the cable. This frees the assembly from the rest of the console. To actually replace the drive, you need to move the lens away from the disc hub by gently turning the worm gear. Flip the new assembly over and connect the brown ribbon that is glued to the metal shield. DO NOT REMOVE THE GLUED RIBBON UNLESS YOU INTEND TO REPLACE IT. After that one is connected, you can slowly flip the assembly and rest is in place. Connect the other ribbons to their respective connectors. Return all the screws to their positions and tighten so they are firm. Don’t go overboard screwing them back in.

Rusty Shackleford - 답글

Hello is the optical drive from my ps2 70004 compatible in my ps2 slim 75001?

Jorick Earl Bastian - 답글

댓글 쓰기

조회 통계:

24 시간 전: 7

7일 전: 41

30일 전: 193

전체 시간: 10,034