메뉴

설정

PlayStation 3 Super Slim Laser Unit Replacement

작성자 ZFix (또 다른 기여자 5명)
  • 댓글 2
  • 즐겨찾기 20
  • 완료: 10

난이도

보통

단계

12

소요 시간

시간 제안??

섹션

1

플래그

1

Member-Contributed Guide

회원-기여 안내서

해당 안내서는 저희 커뮤니티의 멋진 회원께서 작성하였습니다. iFixit 직원이 관리하지 않습니다.

소개

How to disassemble and change the Laser Unit.

도구

해당 도구 구매

부품

지정된 부품이 없습니다.

동영상 개요

  1. Turn off the console and disconnect all cables.

    • Turn off the console and disconnect all cables.

    편집

  2. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws.

    • You must remove the warranty sticker and 4 screws.

    편집

  3. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw.

    • After removing HDD bay cover, you will see another 3 screw.

    편집

  4. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel.

    • Push there to release and remove upper back bezel.

    편집

  6. The upper front bezel is harder to remove. The upper front bezel is harder to remove. The upper front bezel is harder to remove.

    • The upper front bezel is harder to remove.

    편집

  7. Remove 7 screws to release top cover. Remove 7 screws to release top cover. Remove 7 screws to release top cover.

    • Remove 7 screws to release top cover.

    편집

  8. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.

    • Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.

    편집

  9. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable.

    • To release the laser unit disconnect this flex-cable.

    편집

  10. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel.

    • One flex-cable, for rubbers and the metal bezel.

    편집

  11. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.

    • Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.

    편집

  12. Assembling, assembling... Assembling, assembling... Assembling, assembling...

    • Assembling, assembling...

    편집

  13. Let's test the device before fully assembling it. Let's test the device before fully assembling it.

    • Let's test the device before fully assembling it.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 10명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 5명과 함께

ZFix

회원 가입일: 2013년 12월 09일

167,744 평판

안내서 306개 작성하였습니다

배지: 35

배지 +32개 더

팀

Master Techs Master Techs 회원

Community

290 회원들

안내서 827개 작성하였습니다

댓글 2개

의견 추가하세요

Very good job, kudos!

Kevin Borras - 답글

I have found that there are to types of lasers do you sell the second one that does not have the black screws on top but are silver. I have found the one with the silver screws has a smaller laser flex cable and plug. its for the cech-43xx

jack blevinski - 답글

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 16

30일 전: 98

전체 시간: 18,773