주요 콘텐츠로 건너뛰기

기기를 고치세요

수리할 권리

부품 & 도구

소개

If your PlayStation is displaying faulty video, emitting choppy audio, or just isn’t booting properly, the motherboard may need to be replaced. This guide will take you through the process of replacing the motherboard, which houses all of the processors and A/V connectors.

Note: This repair is demonstrated on a SCPH-1001 model. The process may differ slightly if you have a later model.

부품

지정된 부품이 없습니다.

  1. Before you begin, make sure the console is turned off and unplugged.
    • Before you begin, make sure the console is turned off and unplugged.

    • Turn the console upside down and remove the five 15.8 mm-long Phillips #1 screws.

  2. While holding the top and bottom halves of the console together, flip the console back over. Lift the top cover straight up to remove it. While holding the top and bottom halves of the console together, flip the console back over. Lift the top cover straight up to remove it.
    • While holding the top and bottom halves of the console together, flip the console back over. Lift the top cover straight up to remove it.

  3. Remove five Phillips #1 screws securing the metal shield to the controller ports:
    • Remove five Phillips #1 screws securing the metal shield to the controller ports:

    • Two 14 mm screws

    • Three 8 mm screws

  4. Lift the metal shield straight up to remove it. Lift the metal shield straight up to remove it.
    • Lift the metal shield straight up to remove it.

  5. Pull the controller port's ribbon cable straight up and out of its socket on the motherboard to disconnect it. Pull the controller port's ribbon cable straight up and out of its socket on the motherboard to disconnect it.
    • Pull the controller port's ribbon cable straight up and out of its socket on the motherboard to disconnect it.

  6. Nintendo Switch 수리 키트

    A quick fix to get back in the game

    Shop Switch Kits

    Nintendo Switch 수리 키트

    A quick fix to get back in the game

    Shop Switch Kits
  7. Lift the controller ports straight up and out of the bottom case. Lift the controller ports straight up and out of the bottom case.
    • Lift the controller ports straight up and out of the bottom case.

  8. Pull the optical drive power cable straight up and out of its socket on the motherboard to disconnect it. Pull the optical drive power cable straight up and out of its socket on the motherboard to disconnect it.
    • Pull the optical drive power cable straight up and out of its socket on the motherboard to disconnect it.

  9. Use the flat end of a spudger to lift up and unlock one side of the data cable's connector on the motherboard. Repeat this step on the other side of the connector. You'll hear a faint click noise when unlocking the connector. Make sure not to apply too much pressure when lifting up on the connector with the spudger, or else damage may result. Gently pull the optical drive data cable straight up and out of its socket on the motherboard to disconnect it.
    • Use the flat end of a spudger to lift up and unlock one side of the data cable's connector on the motherboard. Repeat this step on the other side of the connector.

    • You'll hear a faint click noise when unlocking the connector. Make sure not to apply too much pressure when lifting up on the connector with the spudger, or else damage may result.

    • Gently pull the optical drive data cable straight up and out of its socket on the motherboard to disconnect it.

  10. Lift the optical drive straight up to remove it. Lift the optical drive straight up to remove it.
    • Lift the optical drive straight up to remove it.

  11. Pull the power supply cable straight up and out of its socket on the motherboard to disconnect it. Pull the power supply cable straight up and out of its socket on the motherboard to disconnect it.
    • Pull the power supply cable straight up and out of its socket on the motherboard to disconnect it.

  12. Remove the five 14 mm-long Phillips #1 screws from the motherboard's metal shield.
    • Remove the five 14 mm-long Phillips #1 screws from the motherboard's metal shield.

  13. From the left side, lift up the metal shield and rotate it about its right edge, opening it like a book. There may be strips of tape holding the right side of the metal shield to the case, necessitating this kind of removal procedure. If there isn't tape, you can simply lift the shield straight up to remove it. There may be strips of tape holding the right side of the metal shield to the case, necessitating this kind of removal procedure. If there isn't tape, you can simply lift the shield straight up to remove it.
    • From the left side, lift up the metal shield and rotate it about its right edge, opening it like a book.

    • There may be strips of tape holding the right side of the metal shield to the case, necessitating this kind of removal procedure. If there isn't tape, you can simply lift the shield straight up to remove it.

  14. Remove the three 14 mm-long Phillips #1 screws securing the motherboard to the bottom case.
    • Remove the three 14 mm-long Phillips #1 screws securing the motherboard to the bottom case.

  15. Lift the motherboard out of the bottom case. Lift the motherboard out of the bottom case.
    • Lift the motherboard out of the bottom case.

결론

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

다른 14명이 해당 안내서를 완성하였습니다.

Craig Lloyd

회원 가입일: 2016년 02월 10일

7,832 평판

안내서 46개 작성하였습니다

iFixit iFixit 회원

Community

108 회원들

안내서 10,315개 작성하였습니다

댓글 쓰기

조회 통계:

24 시간 전: 2

7일 전: 11

30일 전: 72

전체 시간: 19,163