기기를 수리하세요 커뮤니티 상점

PlayStation Move Case Replacement

작성자 Sarah Shand (또 다른 기여자 4명)
  • 댓글 0
  • 즐겨찾기 0

난이도

보통

단계

11

소요 시간

10 - 15 분

섹션

1

플래그

1

Prerequisite Only

단지 전제 조건

해당 안내서는 단지 다른 안내서의 전제 조건임을 참고하시기 바랍니다.

소개

This is a prerequisite guide that will show you how to disassemble the PlayStation Move controller.

도구

부품

지정된 부품이 없습니다.

  1. Turn the controller over and unscrew the four 10mm screws with a PH #00 screwdriver. Turn the controller over and unscrew the four 10mm screws with a PH #00 screwdriver.

    • Turn the controller over and unscrew the four 10mm screws with a PH #00 screwdriver.

    편집

  2. Pinch the sides of the back panel to remove it and set it aside. Pinch the sides of the back panel to remove it and set it aside. Pinch the sides of the back panel to remove it and set it aside.

    • Pinch the sides of the back panel to remove it and set it aside.

    편집

  3. Hold the base of the controller with one hand and with the other carefully pull up on the white spherical piece to remove it. Hold the base of the controller with one hand and with the other carefully pull up on the white spherical piece to remove it.

    • Hold the base of the controller with one hand and with the other carefully pull up on the white spherical piece to remove it.

    편집

  4. Push the Lithium Ion battery from its slot to remove it. Be mindful not to damage the wires or wired components, as the battery will still be attached via its connector.

    • Push the Lithium Ion battery from its slot to remove it.

    • Be mindful not to damage the wires or wired components, as the battery will still be attached via its connector.

    편집

  6. Unscrew the 9mm screw in the battery slot with a PH #00 screwdriver.

    • Unscrew the 9mm screw in the battery slot with a PH #00 screwdriver.

    편집

  7. Using a plastic opening tool, carefully pry the rumble motor free. Using a plastic opening tool, carefully pry the rumble motor free.

    • Using a plastic opening tool, carefully pry the rumble motor free.

    편집

  8. Unscrew the 9mm screw behind the rumble motor slot with a PH #00 screwdriver.

    • Unscrew the 9mm screw behind the rumble motor slot with a PH #00 screwdriver.

    편집

  9. Carefully pinch the plastic sides of the battery slot and lift it (along with the circuit board) from the plastic shell of the move controller. Carefully pinch the plastic sides of the battery slot and lift it (along with the circuit board) from the plastic shell of the move controller. Carefully pinch the plastic sides of the battery slot and lift it (along with the circuit board) from the plastic shell of the move controller.

    • Carefully pinch the plastic sides of the battery slot and lift it (along with the circuit board) from the plastic shell of the move controller.

    편집

  10. Using your fingers, carefully pry the square green piece beneath the battery slot free. It is attached via white ribbons which need to be kept intact.

    • Using your fingers, carefully pry the square green piece beneath the battery slot free.

    • It is attached via white ribbons which need to be kept intact.

    편집

  11. Follow the white ribbon attached to the part you just removed to a smaller, more rectangular piece. Lift the rectangular piece from its slot to free it. Lift the rectangular piece from its slot to free it.

    • Follow the white ribbon attached to the part you just removed to a smaller, more rectangular piece.

    • Lift the rectangular piece from its slot to free it.

    편집

  12. Carefully lift the entire circuit board from the black plastic encasing it. Take extra care not to damage any of the wired components. Take extra care not to damage any of the wired components.

    • Carefully lift the entire circuit board from the black plastic encasing it.

    • Take extra care not to damage any of the wired components.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

작성자

다른 기여자 4명과 함께

Sarah Shand

회원 가입일: 2017년 02월 20일

1,707 평판

안내서 7개 작성하였습니다

배지: 12

배지 +9개 더

팀

USF Tampa, Team S3-G1, Sullivan Spring 2017 USF Tampa, Team S3-G1, Sullivan Spring 2017 회원

USFT-SULLIVAN-S17S3G1

3 회원들

안내서 13개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 0

30일 전: 0

전체 시간: 74