주요 콘텐츠로 건너뛰기
  1. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Power off and remove the memory card. Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.
    • Power off and remove the memory card.

    • Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.

  2. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Using your fingernail or a spudger, pry open the accessory port cover on the top of the device. Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover. Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover.
    • Using your fingernail or a spudger, pry open the accessory port cover on the top of the device.

    • Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover.

  3. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port. Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port.
    • Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port.

  4. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Beginning at the sides of the device, use a plastic opening tool to separate the front and rear cases. Continue working your way around the device gently prying it open. There are still wires holding the front and rear cases together. You may damage the connections if you yank the cases completely apart.
    • Beginning at the sides of the device, use a plastic opening tool to separate the front and rear cases.

    • Continue working your way around the device gently prying it open.

    • There are still wires holding the front and rear cases together. You may damage the connections if you yank the cases completely apart.

  5. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together. Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together.
    • Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together.

    One of the shoulder buttons fell out when I was doing this step, along with the piece holding it in place. They go back in just fine when reassembling but make sure that they are oriented properly, of course.

    klung - 답글

  6. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Using a spudger, free the touch screen controller flex cable by gently prying up the connection.
    • Using a spudger, free the touch screen controller flex cable by gently prying up the connection.

  7. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Free the battery cable by gently prying up on the connection with a spudger.
    • Free the battery cable by gently prying up on the connection with a spudger.

    Any idea what type of pcb header is on the board for the battery? I have a motherboard with a broken header but I cant source a replacement

    Jimbo Jones - 답글

    This is where I screwed up so I recommend extra caution for other newbies. Only the black part is supposed to come off. Don't be an idiot like me and pry off too much...

    ylimakiminna - 답글

    Yea I messed up there too. Is there a way to fix it?

    Alethia Henry - 답글

    This component was far more stubborn than the screen connector when it came to removal. I opted for a smaller tool than the spudger (small flat-head) and managed to disconnect it after determining the best bit size for the job. Screwdriver is metal, obviously, so being gentle helps to avoid damaging anything.

    klung - 답글

  8. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Separate the front and rear cases.
    • Separate the front and rear cases.

  9. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Using the pointy end of the spudger, disconnect the three antenna cable connectors on top of the wireless card. Deroute the antenna cables so that they are out of the wireless card casing. Rest the wires out of the way. Deroute the antenna cables so that they are out of the wireless card casing. Rest the wires out of the way.
    • Using the pointy end of the spudger, disconnect the three antenna cable connectors on top of the wireless card.

    • Deroute the antenna cables so that they are out of the wireless card casing. Rest the wires out of the way.

    Step 9-11 only apply to the 3G version of the PS Vita.

    logicj83 - 답글

    Hello, I have the PCH-2001 model of the PS vita and the right analog stick went out. I ordered a replacement and the stick is slightly larger than the original. The original has a black rectangle on the back, the new version has the star version, which is what you have on this website as the replacement part. Any help here would be much appreciated. Thanks.

    Ben Ragains - 답글

    Can I install a WiFi motherboard on a 3g ps vita model 1100?

    fmind11 - 답글

  10. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Hook the spudger beneath the tab on the wireless card casing and release the tab. Peel up and remove the wireless card casing.
    • Hook the spudger beneath the tab on the wireless card casing and release the tab.

    • Peel up and remove the wireless card casing.

  11. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Remove the two 4.4mm Phillips #00 screws on the wireless card. The wireless card will naturally pop out at an angle.
    • Remove the two 4.4mm Phillips #00 screws on the wireless card.

    • The wireless card will naturally pop out at an angle.

    • Pull out the wireless card.

    My screwdriver does not want to unscrew those. They won’t turn at all.

    Rei - 답글

    My screwdriver does not want to unscrew those. They won’t turn at all.

    Got the same, used PH #0 and grabbed wireless card casing with fingers from the top to release pressure on screen and avoid (possibly) breaking it.

    Yuriy Zhyromskiy - 답글

    Some PS vita models seem to use a T2 screw instead of a PH#00. I’ve encountered this twice now.

    kaosjr kaosjr - 답글

    I replaced de wifi card but is still difficult to connect to wifi. Could it be the wifi antenna? which cable model is it?

    Fernando Diaz - 답글

  12. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Pry up the right shoulder button casing with a spudger and set it aside. Pry up the right shoulder button casing with a spudger and set it aside. Pry up the right shoulder button casing with a spudger and set it aside.
    • Pry up the right shoulder button casing with a spudger and set it aside.

    Is this really necessary?

    fmind11 - 답글

  13. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Remove the translucent, plastic right shoulder button cover.
    • Remove the translucent, plastic right shoulder button cover.

  14. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Release the right shoulder button flex cable socket by using a spudger to gently pry open the tab. Using tweezers, slide the flex cable out of the socket. Using tweezers, slide the flex cable out of the socket.
    • Release the right shoulder button flex cable socket by using a spudger to gently pry open the tab.

    • Using tweezers, slide the flex cable out of the socket.

  15. 이 단계는 번역되지 않았습니다. 번역을 도와주십시오

    Using a spudger, gently peel up the right shoulder button from the light adhesive connecting it to casing. Using a spudger, gently peel up the right shoulder button from the light adhesive connecting it to casing.
    • Using a spudger, gently peel up the right shoulder button from the light adhesive connecting it to casing.

결승점

다른 3명이 해당 안내서를 완성하였습니다.

Brittany McCrigler

회원 가입일: 2012년 03월 05일

86,557 평판

안내서 132개 작성하였습니다

댓글 5개

Is anyone else experiencing the button getting stuck?

Arbo TM - 답글

Yes, mine is getting stuck, too. I am hoping a replacement will solve this problem.

aseelau -

Has anyone experienced or seen an issue where the trigger button acts with the same functionality as the home button. Every time I press the right trigger it exits to home or exits the game.....help please

Daniel - 답글

I followed this guide on my 3G vita in order to replace the right trigger cable. I found it wasn't necessary to remove the wireless card if anyone else finds that part tricky.

Caleb - 답글

i am replacing the whole front part of my vita do to screen cracked and wont turn on, when i put the button back on, how would i do so to make it stick back on? would i need to reglue it or will it stick back on by itself?

Saul Calderon - 답글

댓글 쓰기

조회 통계:

24 시간 전: 1

7일 전: 16

30일 전: 79

전체 시간: 10,869