부품

부품은 필요하지 않습니다.

Unscrew and remove the four screws from the left side of the camera (from the screen's view) Unscrew and remove the four screws from the left side of the camera (from the screen's view)
  • Unscrew and remove the four screws from the left side of the camera (from the screen's view)

댓글 쓰기

Unscrew and remove the three screws from the bottom of the camera
  • Unscrew and remove the three screws from the bottom of the camera

댓글 쓰기

Unscrew and remove the two screws from the right side of the camera. Unscrew and remove the two screws from the right side of the camera.
  • Unscrew and remove the two screws from the right side of the camera.

댓글 쓰기

Open the battery flap and remove the batteries. Keep the battery flap open.
  • Open the battery flap and remove the batteries.

  • Keep the battery flap open.

댓글 쓰기

Use a spudger to gently separate the two halves of the camera's outer casing.
  • Use a spudger to gently separate the two halves of the camera's outer casing.

댓글 쓰기

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Gently pull the half of the case with the screen (the back half) from the rest of the camera.
  • Gently pull the half of the case with the screen (the back half) from the rest of the camera.

  • Be sure not too pull to hard. The screen is still attached to the motherboard. If you pull too hard you will rip it.

댓글 쓰기

The back half (the half with the screen on it) should now be separate from the rest of the camera, but still attached by the ribbon. The back half (the half with the screen on it) should now be separate from the rest of the camera, but still attached by the ribbon.
  • The back half (the half with the screen on it) should now be separate from the rest of the camera, but still attached by the ribbon.

댓글 쓰기

Use a spudger to lift the black flap that clamps the ribbon towards you. When the black flap is open it will be straight up. (like in the second picture)
  • Use a spudger to lift the black flap that clamps the ribbon towards you.

  • When the black flap is open it will be straight up. (like in the second picture)

댓글 쓰기

Now that the black flap is open, gently pull the ribbon out.
  • Now that the black flap is open, gently pull the ribbon out.

  • You should now have the back half of the camera completely separate from the rest of the camera.

댓글 쓰기

This is what the back half of the camera should look like. This is what the rest of the camera will look like.
  • This is what the back half of the camera should look like.

  • This is what the rest of the camera will look like.

댓글 쓰기

Unscrew and remove two screws from the logic board.
  • Unscrew and remove two screws from the logic board.

댓글 쓰기

Pull the front half off of the logic board.
  • Pull the front half off of the logic board.

댓글 쓰기

This will be the front half of the outer case.
  • This will be the front half of the outer case.

댓글 쓰기

결론

To reassemble your device, follow these instructions in reverse order.

Terichael Office

회원 가입일: 2010년 06월 24일

9 평판

안내서 2개 작성하였습니다

Cal Poly, Team 3-4, Johann Summer 2010 Cal Poly, Team 3-4, Johann Summer 2010 회원

CPSU-JOHANN-R10S3G4

4 회원들

안내서 4개 작성하였습니다

댓글 쓰기

조회 통계:

지난 24시간: 0

지난 7일: 0

지난 30일: 1

전체 시간: 1,229