기기를 수리하세요 커뮤니티 상점

RYOBI P422 Body Replacement

필요한 것

  1. RYOBI P422 Body Replacement, Battery and Handle: 1 단계, 이미지 1/2 RYOBI P422 Body Replacement, Battery and Handle: 1 단계, 이미지 2/2

    • To remove the battery press down on the two buttons located on each side of the battery and pull away from the body of the grinder.

    • To remove the handle hold grinder with one hand and use the other hand to unscrew the handle with a counter-clockwise motion

    편집

  2. RYOBI P422 Body Replacement, Body: 2 단계, 이미지 1/1

    • Lay the grinder flat on its side so the screws are facing up.

    편집

  3. RYOBI P422 Body Replacement: 3 단계, 이미지 1/3 RYOBI P422 Body Replacement: 3 단계, 이미지 2/3 RYOBI P422 Body Replacement: 3 단계, 이미지 3/3

    • Remove the four 1.8 cm screws from the lower and mid section of the body with the Torx T20 screwdriver.

    • Remove the 3.7 cm screws from the upper section of the body, with the same screwdriver.

    편집

  5. RYOBI P422 Body Replacement: 4 단계, 이미지 1/2 RYOBI P422 Body Replacement: 4 단계, 이미지 2/2

    • Now that the two halves are unscrewed, lift up the top half.

    편집

  6. RYOBI P422 Body Replacement: 5 단계, 이미지 1/3 RYOBI P422 Body Replacement: 5 단계, 이미지 2/3 RYOBI P422 Body Replacement: 5 단계, 이미지 3/3

    • Remove the safety trigger and the spring.

    • Be careful in removing the safety trigger, the pin may fall out as you are moving it.

    편집

  7. RYOBI P422 Body Replacement: 6 단계, 이미지 1/2 RYOBI P422 Body Replacement: 6 단계, 이미지 2/2

    • Lift up main trigger and spring together.

    • By lifting this trigger and spring out of the handle, you will pull double duty by lifting the black switch box off of its two support posts.

    • Slide the trigger off of the black switch box.

    • Be careful when removing trigger, the spring will be compressed and may move unexpectedly.

    편집

  8. RYOBI P422 Body Replacement: 7 단계, 이미지 1/3 RYOBI P422 Body Replacement: 7 단계, 이미지 2/3 RYOBI P422 Body Replacement: 7 단계, 이미지 3/3

    • Lift the battery lead bracket from its slot.

    • Use the PH 1 screwdriver to unscrew the two 0.7 cm screws that hold the 2.6 cm long brass bracket in place.

    • Use tweezers to remove the brass bracket.

    • During reassembly, remember to keep the spring inside the main trigger and against the bracket that is visible in the second of the accompanying photos.

    편집

  9. RYOBI P422 Body Replacement: 8 단계, 이미지 1/2 RYOBI P422 Body Replacement: 8 단계, 이미지 2/2

    • Flip the grinder over and lift off the second half of the body.

    • Now you can replace your damaged handles with a new pair.

    편집
결론

To reassemble your device, follow these instructions in reverse order.

다른 2명이 해당 안내서를 완성하였습니다.

작성자

다른 기여자 4명과 함께

John Lamanuzzi

회원 가입일: 03/20/15

229 평판

안내서 2개 작성하였습니다

배지: 9

배지 +6개 더

팀

UMass Dartmouth, Team 3-6, Duarte Spring 2015 UMass Dartmouth, Team 3-6, Duarte Spring 2015 회원

UMASSD-DUARTE-S15S3G6

3 회원들

안내서 5개 작성하였습니다

댓글 0개

댓글 쓰기

조회 통계:

24 시간 전: 0

7일 전: 1

30일 전: 6

전체 시간: 1,377